TEA300 Amana Dryer - Instructions

I only had to replace the inside one
I pulled the old one out .
And snapped the other one in

remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done

Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely

used needle nosed pliers, squeezed the latch pop up push new one in. very simple anyone can do it

Was extrememly simple. Just unscrewed the two screws at the bottom front of the dryer and pulled the front of the drayer out. PUshed the broken catch out and snapped the new catch in place. Reattached the dryer front with the two screws and was done. Less than 15 minutes.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.

Followed video on PartsSelect website, they made it real easy.

. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.

The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

Installed the new part. Worked great!

I followed the online video on PartSelect website. No other instruction necessary.

Just follow the video. The hardest part is getting the top to disengage from the clips.