Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TDG546RBW2 > Parts

TDG546RBW2 Tappan Dryer - Parts

All parts for the Tappan Dryer TDG546RBW2

Below is a list of all parts for the Tappan Dryer TDG546RBW2 - Residential, Gas. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the TDG546RBW2
1-14 of 103
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.91

Rear Drum Bearing Kit

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will...

$8.17

Drum Belt

This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is what rotates the drum and tumbles your clothes during the dry cycle. If you can hear the motor running but the drum is not moving that is a sign your belt is broken, stretched, or damaged, and can no longer grip the drum. This belt is 87 3/4 inches long, and is 1/4 inch wide. Because it is made of rubber it is common for this part to become brittle and need to be replaced. This is an authentic OEM replacement part, and it is sold individually. Remember to unplug your dryer before you begin repair work.

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear b...

$19.21

Upper Drum Glide

The upper drum glide is attached to the front panel of your dryer, you can locate it by removing the top portion of your dryer. The drum glide allows the drum to rotate with ease and little sound. The front upper felt glide pad with three nylon glides also includes adhesive, essential for mounting accurately. For this project you will need a putty knife, Phillips screwdriver, and a wire brush. This repair is meant to fix issues such as an abnormal amount of noise or the dryer not tumbling as it should. Consider replacing your belt at the same time if you have a dryer more than 5 years old, as it is likely worn.

$28.01

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...

$14.16

'M' Series Ignition Coil Kit

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the symptoms that this kit could be a solution for are: If there is no heat, not enough heat, or clothes takes too long to dry. In this case, the gas valve coils can be defective and replacing this part will help. Customers rate this project as easy. Refer to the installation diagram for further instructions. For safety, unplug your dryer before repair.

$45.48

Ball Hitch

This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball i...

$10.33

Bearing Bracket

This OEM drum bearing bracket holds and supports the drum bearing in your clothes dryer. The bracket is located behind the dryer drum. Common symptoms that are linked to faulty or damaged drum bearing brackets include: the dryer will not start, will not tumble, or the dryer is making loud squeaking or grinding sounds. If there is an issue with the bearing bracket, it will need to be replaced. Replacing the bracket has been listed as a very easy to easy repair by many of our customers. Remember to disconnect the power to your dryer before beginning this repair.

$8.32

Door Strike

The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. Thi...

$8.61

Grounding Ball

This grounding ball is used in dryers and works to prevent friction in the rear bearing when the drum rotates. If your dryer is making a squealing, loud, banging noise or will not operate, it is best to replace it to solve the problem. To repair, first remove the main top and remove the strap at the back of the dryer to lift the lid. Next, remove the two wire harnesses and Phillip screws on the sides that connect to the front panel. Now that you have access to the inside of the dryer, refer to the manual for further instructions by following the manual provided by the manufacturer.

$29.81

Idler Arm Assembly

Part may differ in color from image. Please note that this is only a cosmetic difference.

$22.09

Flame Sensor

This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off enough heat. If your clothes are not drying at a reasonable time, this might be your first indication of an issue. You will need to remove the two screws underneath the lint cover to remove the top of the appliance. Release the door switch wiring, remove the front panel, and remove the belt off the pully. You should now be able to completely remove the drum from the dryer. This will give you access to the sensor for the repair.

$19.73

Igniter

This part ignites the gas within the dryer. Be sure to not handle this igniter by the gray part as it is very fragile.

$7.88

Grounding Ball Clip

This grounding ball clip is made of metal. Sold individually.

All Parts for the TDG546RBW2
1-14 of 103