Models > TDG336REW0 > Instructions

TDG336REW0 Tappan Dryer - Instructions

All installation instructions for TDG336REW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TDG336REW0
361-375 of 390
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud squeaky noise

  • Customer: Alexander from GREECE NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer was making a horrible squeaking noise comparable to nails on a chalkboard! I looked to get a similar used replacement because I was in a bit of a pinch for $$$, after being frustrated and not finding anything I came here and found all the parts I needed for my repair for UNDER $40!!!! I followed the super easy how to video that was provided on this website. This is the second repair I have made to this dryer, I did the heating element about a year ago. I also used this site to purchase the part and used the how to video associated with that repair. I was very surprised that I received the part the next day when I paid for regular standard shipping! Overall this was a an awesome experience and I have saved so much money repairing my dryer on my own vice paying someone to do it!!!

noisy like metal on metal sound, putting holes in my clothes

  • Customer: shawn from woodinville WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
ordered parts from parts select and tore into it was a breeze wish I would have done sooner.the videos and ideas partselect had made it so simple and I did not have to buy a new dryer like I thought thank god cause I did not have the money to.all I can say is thank you partselect and I will go there for any future appliance problems or parts

dryer was making a shrill noise

  • Customer: Mike from Goldonna LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the front then removed the belt that turns the drum pulled the drum strait up from the top then removed the bushing from the back wall put the new one in I also put A little grease in the new bushing to keep it from wearing installed the drum and front. realy easy. I'm A Instructor at A technical collage in Winnfield Louisiana and I used this as A project for my students.

drum belt

  • Customer: MANUEL from SAN JACINTO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
so easy my daughter installed it the video was very helpful

Loud screeching noise, barrel turned OK and Heater worked

  • Customer: Ellen from Willits CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I took the lower back panel off. Loosened the center bolt and took off the old Idler pulley. It looked brown in the middle and didn't roll well. But I wasn't sure if that was it, because the noise was so loud and sounded metal on metal. So I checked everything and vacuumed everything. After I got the new part it took me about 5 minutes to put the new one on. And dryer works fine. Thanks for the quick response and I saved about $200.00!

replaced rear drum bearing

  • Customer: chuck from carroll NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

no heat

  • Customer: Walter from St Paul MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
no instructions or videos were of this particular unit but the parts appeared to be quite similar across all dryers. Could not find all parts described as potential fails, but found the ignitor to have no continuity. Also replaced ignition coils as they have a high probability of failure. Cleaned everything as well as possible and put dryer back together in reverse of disassembly.

loud noise at back of dryer

  • Customer: sam from prattville AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

Squeaky noise from rear of dryer

  • Customer: Kenneth from Pensacola FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

rear bearing on dryer was squeeking badly

  • Customer: Douglas from Hudson Falls NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.

Dryer made extremely loud rhythmic screeching sound when running.

  • Customer: Paul from Holly Springs NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
DIsassembled the dryer by removing the top piece first. Removed the kick panel and the two screws on the bottom of the front panel. Disconnect the 2 wiring harnesses then remove the remaining 6 screws that you can see from the top. If possible, have someone support the front panel as you undo the last couple screws. Remove the plate on the rear lower right side to expose the pulley and belt. Pull on the tensioner while gently pulling the belt off the pulley and tensioner. Lift the drum up quick and hard to separate the ball shaft from the bearing holder. Remove drum by taking it out through the front opening. Replace the ball shaft on the back of the drum. This is much easier if you have an extra set of hands. At this point, vacuum out as much lint as you can. There is a white container attached to the front panel, vacuum this too. THere was several inches of lint build up that had made it past the screen. Replace the bearing, ball retainer, and ball bearing on the dryer. Grease the ball and retainer and reinstall the drum. SInce I was replacing the bearing, I went ahead and replaced the belt too. Reposition the belt on the pulley and tensioner. Spin it a little to make it is on the right place. Reassemble the dryer. This is the first time that I have done a repair of this sort and it turned out to be a lot easier than I thought. Two people would have made it even easier and faster.

Very loud squeaking

  • Customer: daniel from santee CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed the video, it was good, the instructor's tips were useful and time saving.

Dryer was noisy and had a rumbling sound

  • Customer: Marshall from HAMMONDSPORT NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged dryer power. Pry up the upper cover using a puttyknife along the front left an right corners. Lift cover up and out of the way. Removed the front panel by removing two philips screws, located inside the drum area and pry panel away from unit. Besure to unplug the wires to the door switch before removing the front panel. Know the Drum is exposed. Undo the drum drive belt by reaching in under the drum and pushing the spring loaded idler pulley to the left and remove the belt from the drive motor shaft. Lift the drum straight up, this removes the drum from the rear support bearging. slide the drum out of the unit. Remove rear drum support bearing. and install new brg., being careful not to loose the small ball brearing (thrust Brg.), this proceedure requires two people. Lubricate the support Brg. with a HIGH temp grease. Place new belt on drum and install drum and drive belt reversing the proceedure. Remove old Drum glide and sand paper the old adhesive. Apply adhesive provided liberally to both surfaces, allow adhesive to cure for 10 to 15 min. Allign Drum glide and press and hold in place. Allow adhesive to dry for 2-3 hrs. before installing front panel. Install panel, plugin door wiring close cover. Your Back In Business.....

Drum stopped spinning with any kind of load

  • Customer: Caryn from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I suspected a worn belt and that's what it was. I watched 2 videos on belt replacement and it was not a hard fix. The only "problems" I could foresee would be moving the drum around if you are not that strong. Its not terribly heavy, just a little awkward. I also sliced the top of my hand a little on the underside of the cabinet when moving the drum. Being a little more careful that wouldn't have happened. Part plus shipping was less then $20, and we now have a great working dryer again. I also got a zap when I forgot I had plugged it back in and was putting the inside screws back and the screwdriver crossed some wires. Nothing bad, just a quick jolt. Remember to unplug it until you're all done!

no heat

  • Customer: Edwin from Brooklyn NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove top cover 2 screws then remove front panel 6 screws remove wire connecter on the door panel. ignition coil is on the bottom left side need a short hand srew driver remove 2 screws remove plate holding coils remove coils and connecter. Reinstall in reverse installation. Dryer still didnt heat up so back to the drawing board :)
All Instructions for the TDG336REW0
361-375 of 390