SWS1649HS0 Westinghouse Washer - Instructions

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

Removed front panel and unplugged wire connector to drain pump. Loosened two hose clamps and removed hoses the unbolted drain pump from washer frame. Simple removal and even simplier installation of new drain pump.

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done

Remove front lower access panel: two phillips screws at the lower edge then the panel slid down and off. Removed 5/16 pump mounting screws then slid a shallow pan under pump to attempt to catch stale water, removed left side (inlet) hose clamp and wiggled hose off to drain water with some success, some spillage. Removed outlet hose, turned the pump around to remove electrical connection. Reversed steps to mount new pump and after fighting with spring clamp on outlet side I chose to replace that spring clamp with a 1 1/2" stainless hose clamp which then could be tightened with a screwdriver and only took a minute to wrap up.

Replaced drain pump using this walk through. Different models, but pretty straight forward.

Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.

I ordered pump so I would have it on hand. I didn’t want the washer in pieces waiting on parts. New pump came in 2-3 days with standard shipping. Found a video online for this model. Removed top. Removed control panel and set on front edge of frame. Removed door seal spring. Removed front panel and separated seal from drum. Pump located at bottom left. Removed pump screws. Got a shallow pan from kitchen to catch water. Removed hoses and trap. Not much water. Took trap boot and pump to sink for cleaning and found a bra wire had made it past the screen and was rubbing on pump impeller. That was the noise. Cleaned and reinstalled old pump. Has been running for 2 months without a problem. Easily returned the new pump! Highly recommend this company and site. Will come here for my repair jobs first. Hope I remembered all the steps correctly since it has been over 2 months.

Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.

Simply pressed knob on appliance.

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

I followed the following instructions provided by the parts page and they were EXCELLENT! I had NO problems and was actually enjoyable to fix, thx. to these instructions listed below. Many thanks!!!! FIRST I REMOVED THE TOP PANEL HELD BY FOUR SCREWS AT REAR OF PANEL, PULLING THE PANEL FOWARD AND UP. THEN DISCONNECTED THE POWER AND WATER CONNECTIONS. THEN I REMOVED THE TWO SCREWS HOLDING THE FLOW VALVE TO THE WASHER REAR PANEL,PULLED THE VALVE FOWARD ,REMOVED THE TWO ELECTRIC CONNECTORS, PINCHED THE WATER CLAMP WITH PLIERS AND REMOVED THE WATER CONNECTION TO THE VALVE. THEN REPLACED WITH THE NEW VALVE FOLLOWED THE ABOVE STEPS IN REVERSE ORDER, FINISHING UP BY RE PLACING THE WATER CONNECTIONS AND POWER. THEN CHECKED FO PROPER REPLACENENT AND LEAKS BEFORE REPLACING TOP PANEL

This repair took only about 15 seconds to complete. It just involved pushing the new knob on the selector. The provided video should give you the confidence to complete this task.. I invested $11.00 for the part. I would hate to see the cost to have a repairman come and fix this. Worth every penny

I had to remove agitator and clean under it.

Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.