Models > SWS1339HQ0 > Instructions

SWS1339HQ0 Westinghouse Washer - Instructions

All installation instructions for SWS1339HQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SWS1339HQ0
121-132 of 132
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer was leaking

  • Customer: Donald from Burlingame KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took the front and back off the machine. Removed the old pump by taking out a couple of screws. Put the new pump back in and put it back together. Works fine now.

Clothing/Sheets/Towels snagging in washer

  • Customer: Jeffrey from Smithfield PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
The repair was very simple. Just remove the fabric softener container at the top of the agitator and there was a cover with a little plastic "hook" on the top. Just take a pair of pliers and pull on the hook pretty hard and it pops off. Then using a 1/2" socket, loosen and remove the bolt and pull off the old agitator. Slide the new agitator over the "drive shaft" where the old one was, tighten the nut, put the cap back on, place the fabric softener tray back on, and I was back in business. Works great now.

burning smell from wash, needed new drive V belt

  • Customer: Joseph from Trinidad CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched the video on website, printed instructions for feedback.

washer failed to drain

  • Customer: Gerard from upper sandusky OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
sucked out remaining water with shop vac. took off lower front panel, two screws. took off back panel, six screws. diconnected drain hose from pump,some addittional water drained out, sucked up with shop vac. disconnected tub drain from pump, more water, shop vac. unplugged two wires from back of pump, removed two screws holding pump, removed pump, put in new pump, reversed procedure. Done!

The washer hose assembly had mutiple tears in the bellow section of the hose, towards the outlet net the spout.

  • Customer: Humberto Aarón from Castroville TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).

Washer would flood out the floor now and then

  • Customer: tony from wilmington IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
One day the washer would spill water out on the floor then it would be fine for a week and do it again.Finally it broke,i ordered the new drain pump and installed it in just a few minutes,Hose clamps were a pain,it works just fine now,I would say replace the clamps while you are doing this ,it would make it much easier .Hope this helps !

I was only getting hot water

  • Customer: Elmo from Apache Junction AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.

Belt Had Smoked

  • Customer: Millard from Grand Prairie TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

Unit did not drain

  • Customer: chris from burleson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed and replaced pump

Wouldn't rinse, spin, or pump out the water

  • Customer: Pauline from Kelseyville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

Washer would not spin

  • Customer: Richard from Lafayette LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched the video, all instructions were perfect!

Belt stretched out

  • Customer: Kenneth from Port Monmouth NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,
All Instructions for the SWS1339HQ0
121-132 of 132