SVD48600W Jenn-Air Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven Door Hinges
I never reply to these surveys, but this was so brain dead simple, I had to respond. You take off two safety screws ( the ones that keep the oven door from falling off) You take off 6 screws holding the door together in order to remove the old hinges, put in the new hinges, put the six screws back in that hold the door together, put the oven door back on. Oh, and then put the two safety screws back in the so the oven door does not fall off. The only advice I have is put a big beach towel down to keep anything from getting scratched. Very Easy and saved me a lot of money.
Parts Used:
-
David from Carlisle, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Range had an F-2 code on the control panel
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou
Parts Used:
-
Greg from Frederick, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven would overheat
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Parts Used:
-
MARK from roseville, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Electronic Clock Control Board was out.
STEP 1 GO TO YOUR ELECTRICAL PANEL AND SHUT OFF THE BREAKER OR REMOVE THE FUSE. A drill/driver with a phillips bit and extension is all you need. The 1/4" extension is the correct size for the hex screws. Remove them, then the phillips screws and put aside. Remove the control knobs, then the small screws behind them. Remove the trim and clean as it is most likely somewhat greasey, pull the clock board away from the range so that you can disconnect the wires. Lift the tabs holding the ribbon cable to the board and remove the cable. Now that wasn't as hard as you thought it would be was it? Now reverse the proceedure and you will have a working stove again and will have saved a $100 service call. Don't forget to reset the breaker.
Parts Used:
-
Kurt from Brewster, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Front burners would not light.
First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.
Parts Used:
-
Jeffrey from Columbus, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat
Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call
Parts Used:
-
DAVID from Cape Coral, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
change oven sensor
-
Lloyd from Eau Claire, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!