SVD48600PK Jenn-Air Range - Instructions

The new replacement grease filter came without damage and it was a simple task of removing the old and setting the new in it's place. No tools were required.

Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

Very simple project. Had no clue it was so easy! To test how easy it is, remove the left side grill parts, move the grill parts from the right to the left! I had no idea there was a micro switch in the cooktop to change the fan operation! Parts arrived quickly. Only received one grate of the set, this was quickly fixed by Parts Select Customer service! We only used the grill once, made such a mess! Why did I wait so long to do this! (Over thirteen years!)

Read previous repair story

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

took it out and dropped in the new filter. Total time about 2 minutes

removed two hexigon screws--removed old burner---placed new burner into stove socket--replaced two screws. Done in about five minutes. Most time used to fine right size socket to fit screws! Fast delivery--easy repair--AND it works!

Turned of the power, removed an old element, by unscrewing 2 screws, pulled out element out about 4 inches, remove the slide on connectors, then put them back on that new element, carefully slide in element to the back wall and screw in the 2 screws. Turn the power back on. It is nothing to it. When the old element is out, I took an advantage and cleaned up the inside, using the oven cleaner sprayer.

I watched the video on how to change the oven sensor, which helped me change both the bake element and the sensor. Had a little trouble pulling the sensor plug apart so had help with someone else holding half of it with pliers while I pulled it apart. (It is in an awkward place in the oven and I didn't know how to take the oven door off.) The bake element was a breeze. Had to use tweezers to grab one of the connectors that sneaked back into the insulation. Saved a ton of money. Would have cost more just to have the repairman come--not including parts. Thanks!!!

I lifted the grill off; took the old grease filter out and threw it away; placed the new filter in the well; put the grill back on. Wallah!!! just like new.