SHY99A06UC-14 (FD8212) Bosch Dishwasher - Instructions

With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and slightly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.

I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .

The old Tine holders used on the upper and lower dish rack dried up and cracked/broke. So I purchased new Tine holders for the upper and lower racks and snapped the new parts in place.

To perform the repair, the door panel must be removed (8 Torx screws) and the door removed from the hinges in order to access the lower door seal. For this model Bosch and other similar models, the hinge springs must then be disengaged (safer) or kept from retracting. To disengage the springs requires removing the entire unit, disconnecting the water supply, and flipping it on its side to disengage the springs. I chose the latter, keeping the unit in place, holding the hinges with vice-grips on either side, then removing the door. This was not easy and caution is required. Either method is risky with a 20-year dishwasher.
The replacement part does not fit as well as the original (much sturdier) part, but appears to seal well for now. Repair videos on the internet are for different, newer models where disabling the hinges as described here is not required, making the repair much easier. Recommend looking carefully at your model/manual to determine if the difficulty of the repair is easy or hard.

Turn off power to unit!
-Remove kick panel,2 screws.
-remove water valve, 2 screws, 3 electrical connections, 1 hose clamp.
-Remove elbow from old valve and install on the new valve ( use teflon pipe tape)
-replace valve, hose & hose clamp, electrical connectors and water supply line.
Scew unit in place ,2 screws.
Check for leaks then replace kick panel, 2 screws.

There are two ways to do this repair: the "right" way and the hard way. I chose the hard way, as the right way involves disconnecting the dishwasher plumbing, removing the dishwasher from under the counter, taking all the outer panels off, and disabling the door springs. There are good YouTube videos on this. The hard way doesn't involve that -- but is not all that easy and I'm not sure I'd recommend it. The problem, in essence, is that to install the new seal there is now way to do it without taking the door off the machine and taking the door apart -- which requires that the springs be locked out, if not disabled.

I accomplished that part of it by opening the door, partially, undoing the two screws on each side which hold the hinges, taking the front panel off (piece of cake, with a Torx driver),slipping the door partly off the hinges, and then locking the hinges open with the pry bars.

There are an assortment of ways one could seriously damage either the door or one's self doing it that way -- the hinge springs are very powerful -- so I don't recommend my approach.

Vice grip door hinges. No need to disconnect, un hook hing springs. Works slick. Small vice grips. On hinges. Remove tore screws. Remove seal , and replace seal, reconnect door screws. Boom done.

This is a piece of cake. No tools are actually needed. Grasp one end of the old seal and gently pull it out of the groove in which is fits. Take the new seal, and paying attention to which way around it fits (there is a right and wrong way!) start at either end. Leave an inch or so beyond the groove to rest on the bottom of the dishwasher, and press the seal in place in the groove. You should have an inch or so left at the far end. Go back and go all along the seal and make sure it is pressed evenly and completely into the groove the full length.

You're done.

Dishwasher racks are maddening. It takes years to understand how to make your dishes fit within your dishwasher. We just moved and nothing was working so I did something that I did not want to do--pay attention to the lower rack and figure out why it had a mind of its own. Well, the Bosch interior is filled with adjustable (that usually means problems) fingers. Well, it was not so. A piece was missing that supported the "hand" from which the fingers sprang. That support piece cost about a buck and was available and ultimately on my doorstep in a day or three. Take the part out of the bag, snap it on the hand and enjoy dish racks that don't flop around. Awesome indeed.

REMOVED DISHWASHER FROM CABINET. DETACHED BASE FROM BODY OF THE DISHWASHER. INSTALLED NEW CORD, REATTACHED BASE TO BODY OF DISHWASHER AND REINSTALLED IN CABINET. OPINION: THIS IS A LENGTHY REPAIR AND UNNECESSARY ONE. THE CORD IS PART OF THE DOOR COUNTERWEIGHT AND SUBJECT TO TENSION EVERY TIME THE DOOR IS OPENED, AS WELL AS POTENTIAL CHAFFING DUE TO PROXIMITY TO VARIOUS METAL PARTS, AND VIBRATION. THE CORD SHOULD BE MADE OF STRONGER MATERIAL AND ARMORED OR ALLOWED MORE CLEARANCE. BOSCH SHOULD FIX TO LAST THE LIFE OF THE DISHWASHER.

To replace the part per se was simple. To put everything back in place was more difficult as I took the base of the dishwasher off and a lor of other parts in order to reach for the drain pump. The irony was, after I took appart the base I fount a clip on the internet showing how to do that job and that was a very simple thing, couple of screws to take off the toe plate and the interior liner of the door, to create good access to the drain pump. Really a job of 10 minutes at the max.

Replaced parts

Remove bottom kick plate and raise the feet up. Remove attachment from the top to counter. Slide out. Facing the unit, remove left hand side sheet metal cover. The unit is behind this cover. Unhook the hose on the lower end. Pop the new one in and hook it up!! Test on quick rinse and see results. If ok return to normal as disassembled. Make sure to level the unit after tucking it back in. Enjoy!!

First of all, I quessed at what was causing the droning noise. It seemed that it started when the d.w. was draining. I looked at various sites to try and figure out what was causing the noise but they all wanted money up front before they would discuss the problem. I gambled that it was the drain pump figuring that, oh well at least it's a part I won't have to replace in the future. I got lucky, the noise stopped with the part I bought. The only issues were the wiring harnesss wasn't the same as in the video I used. Overall, your service was very good. The thing I'm disappointed with is the fact that my expensive Bosch d.w. had to be repaired.

I have granite countertops and one of the hold down brackets broke to wood cabinet side mount. Easy and fast repair to remove old brackets, pull out dishwasher, and I replaced both brackets with new, and new wood screws. New installation looks better than original done 18 years ago. Very easy to do and saved a lot of money if I had an appliance repair company do it.