SDE5401AYW Maytag Dryer - Instructions

Removed bottom panel, lint vent assembly, door assembly, removed belt, drum, then heating element from back panel. Unplugged wires from heating element and put them on new element in same order screwed the element back in then all the steps in reverse order. Now I have heat when I run the dryer.
Partselect was extremely fast in shipping my order. I will shop here again!

1.Unplug unit
(gas model, did not shut off)
2. Remove bottom front panel-2bolts
3 Remove main front panel-2 bolts (no need to remove door)
4. Make note of wire colors on door switch and light, disconnect
5. Remove 3 screws that hold air duct assembly(that lint filter rests in) then set main front panel aside
6. Remove lower air duct (to blower motor)-3 bolts
7. Lift and tilt-up top lid/panel of dryer and wedge wood or ? (this will give you easy access and better light)
8. Reach back behind motor to move idler pulley and remove belt from motor & idler pulley
9. Remove 4 bolts and lift up and out front bulkhead frame that holds drum in place
10. Slowly pull straight out & slightly up entire drum
11. Remove circlip/retaining ring, washer, roller, washer and shaft assembly.
12. Vacuum entire unit
13. Light lubricant on shaft when reinstall in reverse order.

Snap ring pliers and a mental note of how the belt is routed on idler will prevent unwanted profanity.
This is an inferior/substandard unit before Maytag bought them. Spend the money and replace both rollers with new shafts (about 50.00). I have spent over 140.00 in parts to keep this unit running (less than 8 years old). So do the math before you start pouring money into this model.

Removed all of the front outer bolts holding in the lower plate, front door assembly, drum outer frame and drum. While removing the outer sheel there are colored wire connections that activate the linterior light and door sensors in which I marked the interior sheel with a marker so I knew which wire went where. Before removing the drum I drew a sketch on how the belt is ran thru the pullys and around the drum, so I would have no problem reinstaLLING IT.The rooler bracket was easily removed with a socket wrench and the retaining wring was pried with a pliers. Reinstallation of the shaft, roller and ring were as simple as removal. I then cleaned the entire interior and lint basket for optimal performance. The most difficult part is pulling the belt back around the drum, but still not very difficult. Finally I reattached nall removed parts as they were removed and I now have a like new dryer for about $20.00 vs, buying anew one or repair fees costing Hundred$ OF DOLLERS.
Thanks Partsselect.com Again!

There was no repair, just replacing the old, wornout lint filter. But I wanted to thank you for the ease in finding the part and for your prompt delivery. I really appreciate that. If we need any other parts we will order them from you.
Thanks again!

(Used joe From Beacon Falls Instructions)
UNPLUG THE DRYER FIRST
1. There are two bolts on the back of the dryer that connect the control panel and the dryer. Remove these bolts with a socket wrench and their brackets. Set aside.
2. Lift up rear of dryer top a few inches to locate two metal flanges on the front top of the dryer. Lower the back side. Now on the front of the dryer, insert the flat head of a large screwdriver (cover flat head with rag to prevent scratches) where the flanges are located and pry upward, one side at a time. It does not take much pressure until the top “pops” open. Repeat prying motion on other side of front dry to free the top.
3. The top of the dryer is now loose and can be slid backwards enough to see down the front of the dryer. Locate two screws (one on each side) inside the front panel a few inches down. Use the same socket size with wrench to remove these two screws.
4. Notice there are three wires that connect for the light on the right hand side. With care, these can remain attached. Alternately, take the time to write down the color and order and remove these now
5. Pull the front panel towards you slightly and lift up. The front panel will now come free and can be set aside. If you did not remove the wires, the front will need to be propped up close enough to the dryer so that the wires are not ripped out.
6. Remove the three Phillips Head screws located inside the dryer drum that attach the Lint Duct Assembly. Pull out the old assembly. Vacuum out if necessary.
7. Insert the new Lint Duct Assembly and secure with the three screws.
8. Reattach dryer front and top.
9. Done.

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

I removed 3 screws to open panel, removed defective switch, replaced with new switch. Reistalled panel, tested machine. Saved myself $100.00 service call charge plus having to wait for 2 weeks to have repair done. Priceless..........

I went to RepairClinic.com & FixYa.com for some great advice. I searched the internet for the parts. PartSelect.com was the most inexpensive. Delivery was good. Using the repairman's manual I found on the internet I followed the steps to remove each panel, in order. The wiring was the most bothersome, but okay to resolve; write it down and pull it off! I don't think the rollers, in the back, were bad. The tension idler was extremely worn. I tightened the tension idler bracket at the base. I did need to use an O-Ring Spreader to get all the rollers off and on. Although there were more panels to remove than older models, it was easier! Wrap the belt around the drum before reinstalling. The belt will loop around the drive & tensioner relatively easy. Replace the rubber seal around the drum & replace all the panels. Things are quieter now than I can remember in a long time.

watched video for Each Part

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

Unplugged dryer.
Removed front control knob and removed two bolts behind it using 1/4" nutdriver.
Unscrewed three phillips screws along top of control panel.
Using slight shaking motion to release tabs, removed control panel from top/back of dryer and pulled forward.
Using needle-nose pliers as necessary, removed electrical lines from old timer and inserted them onto corresponding tabs on new timer. These are color-coded, but I found it just as easy to move each line from one timer to the other in order as I removed them.
Used nutdriver to attach new timer to control panel.
Reattached control panel to top/back of dryer and reassembled housing using the phillips screws. Reattached control knob.
Plugged in dryer.
Took me 35 minutes -- I am a 70-year old woman who has never done a repair like this before!

took one out - put new one in

Unable to find a repair manual or accurate diagram, I forged ahead and removed the top and front panels of the dryer. It took two tries to figure out how to thread the belt (nine of my ten thumbs kept getting in the way!), but after a coffee break, the job came together, and I've taken the clothesline down!

Once I was able to take apart the door assembly, I was able to determine that I needed the lint duct assembly. The parts website was very helpful with diagrams and explanations so that I could order the part with confidence. Since laundry is so important in our house I paid for expedited shipping. The part arrived in Florida less than 24 hours after it was ordered and soon after it was installed and the dryer was working properly.

Removed back cover of console,using screwdriver and nut driver. Removed old switch by squeezing the end tabs and pulling switch out. Removed wires on switch with pliers. Placed wires on new switch using pliers. Snapped new switch back in place. Replaced back cover to console with screwdriver and nut driver.