SCA1000DWW03 General Electric Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Parts Used:
-
Pines, from Middletown, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Could not be turned on
Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.
Parts Used:
-
Remer from Dothan, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken latch hook
Removed. Inside frame with putty knife replace new latch attach spring and line up notch of latch in slots. That was the most difficult part replace inside frame. Done!
Parts Used:
-
David from Pittsburgh, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Broken microwave glass tray
-
Frank from Arlington, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The handle broke off where the screws enter the handle
This seems to be a fairly common occurrence so I've repaired this multiple times, once a year on average. The on site instructions are clear. Lift the top vent area off so you can remove the door. Open the door all of the way, lift off of the bottom peg and pull from the top. Lay door on a flat surface and with a small flat head screwdriver, gently pry the frame up (part 1804, door chock cover). There are small plastic tabs holding this part: use caution as they break easily. Once removed, on the door assembly, remove the small Philips screws: push the plastic tabs back, one side first; this part should then slide out. Both door handle screws are the exposed. Remove these (probably holding the broken handle parts, use the small screwdriver for lift to remove parts). Place the new handle on the door and replace the screws. replace the door assembly, be sure to lock all of the tabs back in place, snap door mask in place, replace door.
Parts Used:
-
Lou from Monarch Beach, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Change a burnt out bulb
Opened the lid over the bulb by removing one screw. Removed old bulb; a bayonet type with delicate prongs. Inserted new bulb. Best to turn off circuit breaker toi the micro for safety reasons.
Parts Used:
-
George from Fort Myers, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken plsastic
-
Brian from Lakewood, WA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The Vent Grill Tabs that hold up the vent Broke
The Vent Grill came off when the two Tabs crack and broke off. The New replacement from PartSelect arrivied. Took the part out of package and replaced the two screws on top of the Vent. Had to push the Vent in to align the first screw. Pushed the side of the vent to align the Tab and put the second screw in. The fit was perfect
Parts Used:
-
Steven from Cerritos, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!