Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SAV5701AWW

SAV5701AWW Maytag Washer - Overview

Get Parts and Repair Help for SAV5701AWW

If you know the washer repair part you need, you can browse the list of all parts on the SAV5701AWW, or you can search by name or part description. You can also find your part by where it is located on the SAV5701AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for SAV5701AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.15

Washer, Thrust

This washer is 3/4 inches in diameter.

Order within the next 3 hrs and your part ships today!
$5.15

Hose Clamp

Order within the next 3 hrs and your part ships today!
$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 3 hrs and your part ships today!
$10.11

Retaining Ring

This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.

Order within the next 3 hrs and your part ships today!
$4.09

Timer Knob Insert Cap

This timer knob insert cap is just over two inches in diameter. It is all white in color and is made of plastic.

Order within the next 3 hrs and your part ships today!
$5.51

Hose Clamp

This hose clamp is sold individually.

Order within the next 3 hrs and your part ships today!
$5.15

Lid Hinge Mounting Screw

Sold individually.

Order within the next 3 hrs and your part ships today!
$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Order within the next 3 hrs and your part ships today!
$21.83

Idler Pulley Wheel

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 3 hrs and your part ships today!
$7.60

Spring Retaining Clip

This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 37 of 42 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

unusually loud rumbling in spin mode, no spin out

  • Customer: Ralph from Moreno Valley, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 27 of 32 people found this instruction helpful
removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. D... read more

Bad shaking During Spin Cycle

  • Customer: Gary from Park Ridge, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 31 of 48 people found this instruction helpful
firsted layed washer back On A Angle For Easy Acess To Motor Removed Both Hoses And Four bolts pulled Motor Assembly out replced belt @ idler Pulley Reinstalled Motor. read more