S61STRP Maytag Refrigerator - Instructions

Ice door flap was broken and warm air was getting into the freezer. I removed a total of 4 screws to get to the flap. Total time was less than 15 minutes and very easy. Partselect customer service was very helpful and friendly. If you have any questions, do not hesitate to call them. They were very helpful! I have this site bookmarked!

Pull out fridge and unplug
Remove drip tray from dispenseer
Unscrew face plate (star bit) 2 screws
Carefully disconnect wire strap from faceplate controls
Unscrew dispenser from chute - 3 screws and one is hddend next to actuator.
Carefully disconnect another wire strap to remove unit.
Remove actuator pad
Remove limit switch (i small philips screw)
Replace switch & pad
Re-assemble

Neither the actuator pad nor the limit switch appeared broken or worn but it appears to have solved the problem.

Not a terribly complicaed repair but you need to take care not to damage anything as you take apart. More work than just changing a filter or bulb.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!

I first removed the tray at the bottom of the Ice/water compartment, 2nd, removed the 2 star headed screws that are visible and 1 star screw near the water hose. removed front pannel. 3rd removed 4 star screws holding ice/water assembly, let this hang down and was able to reach in and removed the round broken shut door. replaced with new door, Difficult to get new door in but I was lucky and got both side wings in the proper slots. Did everything from above in reverse. New Ice doot works great. I just wish you had sent some type of instructions! Very happy with your company. Other web sites wanted me to buy a complete kit just to get the door assembly. you saved me $30. Thanks

I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.

Installing the seal was fairly easy. the seal as arrived from vendor was very deformed. It came with no instructions. I was able to use a hair dryer to heat the seal and soften the rubber. While softened I pressed the seal into the frame. It slowly began to hold and take shape. Some areas where the seal had been folded in the carton took foam filler to hold into position.

I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.

Upon careful inspection, I found that the dispenser also would occasionally fail to shut off when dispensing whole or crushed ice, which led me to think that the problem was in the dispenser actuator rather than in the water solenoid or fountain switch control board. To inspect the actuator mechanism, I shut off power to the refrigerator, removed the escutcheon mounting screws, the escutcheon, the cable from the fountain switch control board, and finally the fountain bracket assembly. There was a small amount of hard water scale on the back of the actuator pad, but no groove in the plastic part of the pad that actuates the switch. I replaced the pad and switch (1 screw) and reassembled the dispenser. The dispenser no longer sticks and shuts off normally.

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

Step 1 :I had to remove the ice drip tray just pull it out.
Step 2 remove the 4 or 5 screws holidung in the control module (push button display pad)
step 3: pull the plug from the diaplay panel
Step 4: remove broken door from slot and slide new one in. Be carfull not to let the brass plug fall out of it does it just slides back in.
Reverse all steps your done about 20- minutes..I am a building engineer by trade. I think the average person 30 to 60 minutes..

followed the instructions provided and that's it!

Very easy to remove one screw holding the enclosuer, then unplug the wire harness, remove 4 screws holding the solinoid, and the 4 screws holding the auger motor. The hardest part was removing the auger from the shaft of the motor. this took most of the time. reassembly went very fast.