S5200E6WW General Electric Washer - Instructions

Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done

I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.

There are many on-line videos to help you do this. It's so easy, even a beginner handyperson can do it. For this model, just run a strap under the agitator to assist you in lifting it up off the coupler (good tug). Remove the old worn coupler, put the new one on, set the agitator back on by giving it a little downward push.

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

As directed by the book.

Pulled off agitator with little effort. One 7/16 bolt to remove and the coupler came right off. Pushed on new coupler, replaced with new provided bolt, pushed agitator back on and was back in business!! Very simple inexpensive repair. Thanks Partsselect for your quick parts turnaround!

Once I watched the video to replace the pump(Thanks so much for that - big help!!), I disabled the machine to replace the pump, to my surprise found a big clump of fuzzy stuff that was blocking the pump, once I removed that and re-assemble the washer, it started working fine!. Unfortunately, I had already bought the the pump and agitator bell thinking they where both bad, so I'm in the process of returning them now, thanks a bunch! btw - what took so long was I had a mess with the water left in the washer, tip - get all the water out first ;-)

Pulled up agitator, replaced coupling kit, pushed new agitator onto new coupling kit. Took less than 5 minutes if that.

This top loading washer was purchased new in 2006. It has had a good bit of use and was a rather inexpensive model, but had been working fine. Suddenly the agitator stopped working. First I pulled off the agitator inside the machine, which in this model came off in one piece. In order to do that I grabbed it at the very bottom by pushing my fingers underneath the base, then rocked it from side to side while pulling up on it until it popped off. This exposed the agitator gear that had gone bad. I unbolted the gear and pulled it off. This removal took a bit of effort, and again, we had to rock it back and forth while pulling up on it until it finally came loose. When the new part arrived a few days later, we slipped it onto the transmission stem, and bolted it into place. Then the agitator was put back on and snapped into place. Works as good as new for less than $14, including shipping!

Viewed the hot/cold valve. I saw that the cold water solinoid was burned. Ordered new valve and replace old valve. On my washer 4 screws held the switch panel, easy to remove and gave me plenty of room to veiw and do the repair.

I found the diagram in your website, identify the problem, order the replacement part and replace it in 10 minutes. Great deal, thanks.

Watch how to fix it on You Tube. Order the part I needed and fixed. Real simple. That is it.

1. Removed the control knobs from unit. 2. Removed the five hexs head screws that secured the control panel to unit. 3. Lift the panel up and out and laid panel face down on unit. 4. Unplugged the three connectors that plugged into the control assembly. 5. Removed the three screws that holds the control assembly to the panel. 6. Replaced with control assembly in reverse order.

order part. replace

I watched the video you provided and I could't believe how simple it was. I'm 67 yrs old and I just followed the video instructions.