S5200E6WW General Electric Washer - Instructions

My washer was full of water after it wouldn't drain as part of the wash cycle. I used a Wet/Dry vacuum to remove the water from the tub. Followed the video provided on this part page. When I pulled the hose from the wash tub to the pump at least a gallon of water that I was in the bottom of the tub and hose rushed into the base of the washer. It was an unexpected mess to clean up a the end of the job. Pump was fairly easy to remove from the washer, but reinstalling the hoses to the pump was slightly more challenging. The hose from the tub to the pump is about an inch too short to make this an easy fit. I had to have my wife hold the hose clamp open with the channel locks while I positioned pump onto the hose. After the hose was installed, the second hose was much easier to install. With the new pump the washer running like a champ!

"Thought" the belt was the problem - ordered new belt - waited for belt to arrive - opened washer. Belt was in perfect condition - problem is the clutch. Next time husband will verify problem before ordering parts.

Changed the dual water inlet valve.

New dual water inlet valve.

removed top and replaced .

I took the two screws out that was holding the bracket and hose in place. I then pulled the hose out and then had a little bit of a hard time taking off the bracket (it was plastic and felt if I bent it to hard it would break) wiggling it down to the end of the hose. Re inserted the hose attached bracket, and I was done.
It would have cost me a lot more then $20.00 to have a repair man come in and fix it.
Love the service, delivered in two days.
Will use them again.

Pulled off front cover of machine. Unplugged unit. Used a channel lock (water pump pliers) to squeeze the hose clamp on the suction hose. Pulled hose off of pump suction. Did same for discharge hose. Some standing water came out onto floor of unit. Unscrewed 2 screws from base using nut driver. Pulled the 2 wires off of the stabs of pump. Re-installed new pump in reverse order. Unit back on line in 15 minutes, and works fine.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

First i removed the bottom of washer and removed clamps from two hoses connected to the pump , removed 2 pump bolts along with wire connector. Then reinstalled new pump, hoses and wiring and that was it. Very easy !

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

R & R drain hose

The staff at parts Select are one of a kind, my order came before expected. Thanks Parts Select

Replaced the button and was working in less than Fifteen Minutes.

Was easy to remove the broken parts because they were loose already due to the broken finger in the agitator. It was good that I ordered the coupling kit because the bolt showed corrosion already. With the new parts I was able to see how they all clipped on together so I set myself to unbolted the coupling, install the new coupling, tighten it, alined the agitator to it, pushed into place and,... vuahla!!! fitted and worked like a charm.

Used pliers to remove old clip. Installed new clip and knob. Very easy.

Step one: Order the Belt and the $10.00 tool that fits on the motor sprocket to keep the belt from slipping off. Step 2: Lean the washer back at about a 45 degree angle, you may have to disconnect the water lines to achieve this. This puts the machine in a good position when you sit in front of it as you are installing the belt. Step 3: Install the tool over the motor sprocket leaving the grooves exposed. The belt fits in these grooves. Step 4: Slip the belt over the motor sprocket first and than the large sprocket wheel behind. This will take a little muscle as the belt is considerably smaller. After a couple of attempts at rotating the big sprocket the belt kept slipping off. I than took a plastic tie and strapped it around the belt and the big sprocket wheel, this kept the belt from slipping off as I rotated the wheel. Once the belt is on snip off the plastic tie and you are home free.