S1050EH-Z Admiral Range - Instructions

Elsie from Garner, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

To Old Needed To Be Replace

Actualy I just removed the old ones and replace them with the new ones . And thank you for your prompt delivery I found some one I can trust . Thanks again . Mrs bolanos

Parts Used:

ROSARIO from MESQUITE, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

rusty pans

simply remove the old and install the new; perfit fit

Parts Used:

Stewart from Hanover, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Surface Burner not working

I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new bracket and installed the burner. double checked everything and lowered the top. Done

Parts Used:

Cody from Abilene, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

I needed to replace my burner pans.

The Drip Pans are a cinch to replace with no tools necessary. The best part is that the Web Site is extremely easy to use, and the parts arrived two days after being ordered.

Parts Used:

Robert from Wilton, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

drip pan were burnt out

simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.

Parts Used:

Delroy from Miramar, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Easy installation

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

Parts Used:

Bake Element (15 Inch long x 19 Inch wide)

Jeremie from Freeland, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Drip bowls were all rusted.

Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

Parts Used:

Robin from Seneca, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

old drip bowl was worn out

new drip bowl fit perfectly and was a snap to install.

Parts Used:

Richard from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

burner not working

burner was shorting out replaced part works great

Parts Used:

gene from kent, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

burner would not heat up the connection was bad

loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.

Parts Used:

Earl from Union Mills, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

two of the burners were working intermittently

I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.

Parts Used: