Models > RVM1535DM2BB > Instructions

RVM1535DM2BB Hotpoint Microwave - Instructions

All installation instructions for RVM1535DM2BB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1535DM2BB
181-193 of 193
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Handle broke

  • Customer: Alma from Inverness FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took inner panel off around window,took outer facing, Took broken handle off and installed new handle and reassembled.A piece of cake.

Insulator around light socket Broke.

  • Customer: Karen from Springfield IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took out five screws on microwave bottom, removed the two screws in the socket and unplugged the light socket. Plug in new socket, screw in place with 2 screws. Lock in microwave bottom,and screw in 5 screws. Replace bulbs. Be sure and either unplug microwave or switch off at electric service box, before starting. Of course, hubby did all the work, but I supervised.

the light over the stove top went out

  • Customer: charles from st augustine FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.

Quit working

  • Customer: William from Socorro NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just like the directions said. Very simple.

fan came on when door was opened.

  • Customer: Hugh from Albertville AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First, there are three door operated switches in this model. The monitor sw, the secondary sw (both of these are on the bottom in the same bracket) and the door sensing sw on top. The door sensing and secondary switches are both N.O. and have the same part number (probably why you show just two switches). The monitor sw is N.C. and it was not my problem. The secondary sw was bad on my oven but I had replaced the door sensing sw (which wasn't bad) on a previous order and kept the old one so I used it to make the repair. All three switches can be accessed without removing the oven by removing the discharge louver (remove two flat head screws on top and slide the louver to the left) then carefully remove the control panel (one screw on top and lift out). The switches are held in place by a plastic tongue that fits into the rear mounting hole on the switch. I used a common screw driver with a small tip to gently lift the tongue and slide the switch out with needle nose pliers. The new switch just snaps back in. The switch holder bracket looks like it would be easily broken so be gentle. I don't know what the symptoms would be if either of the other switches were bad so I would recommend buying all three and you would have them if one of the others failed in the future. The information I gave on the switches came from a schematic I found inside the control box. Hope this is helpful.

Motor and fan turned on when door was opened.

  • Customer: Neal from White House TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Loosen the two long anchor bolts that screw into the top of the microwave cabinet. These are usually in a shelf or cabinet directly above the microwave. Tilt the microwave forward enough to remove the 2 Phillips head screws from the top of the microwave cabinet. They are near the front. When these two screws are out, remove the fan vent. Once the fan vent is off, remove one screw that holds the control pad in place. Let it hang down. Just to the left of the control pad, you will see wires leading to three switches that close when the door is closed. Use a torx driver to remove the two screws that hold the switch bracket in place. With the bracket out, unplug the wire harnesses. On the opposite side of the wiring connected, a tab holds each switch in place. Lift the tab and slide the switches out. Usually, the bad switch will be identified by a loose or broken spring. Test them by pressing down on the switch. If you notice the bad switch spring, this is usually the bad one. When you have the new one, simply push it back into the appropriate slot and be sure that the holding tab snaps back in place. Plug the wires back in and re-attach the bracket. Put the control pad back on, then the fan vent. When down with those, push on the bottom of the microwave to lift it back into place and tighten the two anchor bolts in the top.

Fan stayed running when door was open...all else working fine

  • Customer: Marla from Arlington TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First, unplug microwave. Unscrew two screws at top of microwave, slide grill cover left and remove. This allows access to single screw holding control panel. Remove this screw and lift up control panel to remove. Secondary door switch is black switch at lowest position. The switch is held in place by a lever in back and very hard to get to. Remove the wires plugged into the switch, then remove two screws holding the plastic switch mount that holds all three switches. These screws use a "star" type screwdriver. Once the plastic mount is free, lift it up, right, and tip it slightly to find the lever that will release the black secondary door switch (the lowest switch)...release the broken switch, snap the new switch in its place. Replace the plastic mount by lifting and replacing back into position and replace the two "star" screws. Now, replace the wires onto the new switch, and test operation. Replace control panel, and top grill. It goes faster than it writes...getting the old switch out through that difficult to reach lever was the hardest part...still less than thirty minutes.

Burned out light bulb in the over-stove microwave

  • Customer: George from Arlington TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the one phillips screw that holds the light lens in place, drop the lens down for access to the burned out bulb, screw in the new bulb, replace the lens.

light bulb fused it self to socket

  • Customer: CHRIS from SPRING TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replace socket

Bulb separated from base, leaving base in socket. Unable to remove base without damaging socket.

  • Customer: Danny from Zebulon NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 5 phillip screws from bottom plate of microwave oven to lower the plate and gain access to the socket. Then, removed screw(s) attaching socket to the oven. Installed socket, and secured the bottom plate of the oven with screws removed previously.

over-stove lights burned out, one fell apart while removing

  • Customer: Nancy from Tempe AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed suggestion by previous poster to remove bottom panel...facilitated process well

Replace stovetop light socket

  • Customer: Tim from Pasco WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

Converted an over the range microwave from non vented ductless to outside vent.

  • Customer: Emanuel from Woodstock VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.
All Instructions for the RVM1535DM2BB
181-193 of 193