RVM1335WC001 Hotpoint Microwave - Instructions

Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.

The part arrived very quickly - within three days of my order. It was a little challenging to get the broken handle off - you have to hold the plastic screw inserts with pliers or another screwdriver to prevent the screws from just spinning in place. Once secured from spinning, I was able to remove the two screws that attach the handle to the microwave door. The new part went on easily, but the fit of the new handle was snug and the screws a little difficult to drive. It helps if you push on the handle to keep it tight as you drive the screws. The entire repair was completed within five minutes and the microwave was "back in business". This repair can be easily completed by someone with little mechanical ability.

I asked a handyman at the local fitness center about repairing it and he refered me to your website where I found an exploaded drawing showing the parts I needed and how to get to them. It was great and very easy.

Just unscrewed the screw holding the lens, unscrewed the bulb and put the new bulb in. Simple

so easy, but how do i turn light off?

Part recieved next day. thanks so much

My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

Removed broken coulper.Snaped new coulping in placed.job done.

Unscrewed the lens, it hinged down, then I could remove the frame. Pulled old bulb out and replaced with new one. Replaced broken glass in frame. Reset hinge into the holes and swung it up into place. Screwed it in.

Very easy!

changed the bulb

All one has to do is use a screw driver to remove the screws, one per lens.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.

Less than 10 minuits.

With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

Replaced the fuse. Result; did not fix the problem.

Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.

Since the job required replacing both the bulbs and sockets the unit was dropped from the wall. Used a towel and plywood to protect the range under the unit. Then these steps: Unplugged the power cable and placed a support board under the unit while removing three bolts from overhead cabinet. Next, removed support board and with a helper rotated the unit down and lifted it out of the rear wall mounting panel. Then turned the unit upside down, removed the bottom plate and unplugged the feed wires and two wires to each of the sockets. Next the single screws holding the sockets were removed and the sockets extracted from the mounting shells and new units were installed. When remounting the unit it was necessary to start all three bolts from the upper cabinet just a few turns and then tighten the center bolt completely first.

removed the lens cover with one screw and replaced bulb