Models > RVM1325BW03 > Instructions

RVM1325BW03 Hotpoint Microwave - Instructions

All installation instructions for RVM1325BW03 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1325BW03
46-60 of 151
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Micrwave won't run - turntable turns backwards when door opened...

  • Customer: Roger from Fountain Hills AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Bulb burned ot

  • Customer: John from Fort Smith AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base

The handle on the "over the oven" microwavce just came off due to broken plastic.

  • Customer: JOHN from CHESTER SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I removed the one remaining screw. PLaced the new handle on the door and used a phlips head screwdriver to screw the 2 screws in place.

While reheating food, the plastic door handle snapped off in my hand!

  • Customer: Cynthia from Bakersfield CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Ordering was easy! I used the model # on micro and found the diagram which told me exactly what I needed to fix it! It arrived in 2 days from when I ordered and all I really had to do was uncrew the old tap screws using a needlenose plier to hold sheered off end of plastic mount and phillips head to unscrew and then re install new handle! So easy! I didnt even need to wait for my husband to get home!

broken handle on door

  • Customer: Randy from Sandwich IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Installed new handle with the two ordered screws. Everything fit. Quick repair. Though I believe the handle to be a little pricy.....when all is finished and all works properly one can overlook what ones feels is a little pricy. Also much cheaper than a entire new unit. Thanks for prompt delivery.

Power worked but would not cook

  • Customer: Jim from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

Microwave handle broke off

  • Customer: DANIEL from ATLANTA GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Super easy. I had to grasp the remaining plastic handle nubs with a pliers while unscrewing the screws with a philips head screwdriver. Save the screws -- the handle does not come with them. Attaching the replacement handle took about one minute.

Broken lens

  • Customer: Norman from Voorheesville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
remove two screws bend out flaps remove broken glass install new glas bend flaps back to hold glass install two screws. Done.

Previoous glass lens was broken

  • Customer: Tommy from Santa clarita CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.

This repair can be don in under 5 minutes, easily !!

The handle on my microwave broke off

  • Customer: Sherry from Golden CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I ordered a new part on partselect on monday and had the part by wednesday. It was installed in 5 minutes and nowi can use my microwave withour jamming a microwave between the door and the base.

Door handle Broke

  • Customer: George from Wildwood MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Took the old one off with a phillips head screwdriver and screwed the new one on. Very Simple!

The handle broke on the microwave that was installed to the cabinetry

  • Customer: CINDY from PALM BEACH GARDENS FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
We removed the screws, they were broken so we needed pliers to hold one end of the screw while we twisted the other end.
After that we simply screwed the new handle in.
I ordered exactly what I needed, the new screws were separate. But I looked at the pictures of the parts and made sure I had the correct parts to finish the job. I did. The parts were there in 2 days and we had the microwave fixed before Thanksgiving.

Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.

  • Customer: Leon F. from Brookline MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.

Light bulb wouldn't light.

  • Customer: Steven from Marina Del Rey CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.

Light bulb burned out and assembly broke when trying to replace bulb

  • Customer: Jeanne from Kirkwood MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I used the internet and your directions to complete the repair. It was easy!
All Instructions for the RVM1325BW03
46-60 of 151