Models > RUD5750HB0 > Instructions

RUD5750HB0 Roper Dishwasher - Instructions

All installation instructions for RUD5750HB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750HB0
151-165 of 165
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking into empty dishwasher.

  • Customer: Albert from High Point NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
After emptying the dishwasher the bottom had no water in it. A few hours later there was water in bottom. This told me the inlet valve was leaking. I took the bottom kick plate panels off. Directly in front on left side was the water inlet valve. Remove mounting screw, disconnect electrical connection, the water feed and discharge hose and remove valve. Install new valve. 100% DONE! Reinstall front panels after checking for leaks. At 71 years of age my typical 20 minute job actually took less time.

The soap dispenser lid spring was broken.

  • Customer: craig from eighty four PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I watched the video, which was very good, and did the repair. It took about 10 minutes. Most of that was watching the video. EXCELLENT VIDEO!

Heating element would not heat

  • Customer: Jim from Republic MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Water leaking from door

  • Customer: Kenneth from East Providence RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just followed the online instructions. I used white vinegar to clean any residue first. So easy.

The plastic brackets that hold the screw against the frame had broken

  • Customer: Rahul from Irvine CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the Access Panel retainer from top of the panel. Then remove the Access Panel and the Spacer Panel from the front. Then remove the Extension from the bottom. This step was kind of difficult, I ended up bending the plastic bracket on the pane since I was going to throw it away anyway. Install all the parts onto the new panel in the reverse order. Screw the panel back on to the dishwasher.

Rusting lower rack

  • Customer: Todd from Sylvania OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced the lower rack. The replacement part had the wheels attached. No assembly required.

water leaking from bottom of door

  • Customer: Mary Ann from Menahga MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the 2 water deflector and slipped the new ones in , in place.. very easy to do but it didn't seem to stop the leak so ordered the door gasket

top basket wheels worn out

  • Customer: Carl F from liberty TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
used a common screw driver. took the ends off then pulled out the basket . used the screw driver to pop the brackets with wheels attached. new ones back on and about twenty minutes done. very easy.

Leaking where motor drive shaft enters pump

  • Customer: Steven from Woodstock IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

the tips of the rack were rusting.

  • Customer: Gary Scott from Bonham TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received new rack in record time(very impressed with the delivery time)installed one part for the removable rack in the rear and simply replaced the old with the new.

Broken Hinge Lid Pin and Lid Spring

  • Customer: Jan from Chatsworth CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video's from Parts Select and it took me less than 3 minutes to replace these parts. I did find it easier to use a screwdriver to lift the u shape of the spring over the detergent cup as the pliers tended to pull on the spring too much. Couldn't have been easier or faster, awesome!

Dish washer not draining

  • Customer: danny from pinehurst TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I looked up my problem on your site and it took me to the parts most common for that problem. Your site listed the exact parts needed for my model. Got the parts and followed the direction on posted on your site by Andy.The parts were right on when I got it apart the impeller was locked up. Changed the parts without a any additional problem also took the check valve off of the underside front where the drain hose connects and cleaned it. The check valve had string and a tooth pick stuck in it. After all that hook water back up ,turned power back on and it works like a charm. Great site, parts are reasonably priced. Thank you Danny

Old basket broke

  • Customer: Henry from Manteca CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed old basket, replaced with new one.

bad door switch

  • Customer: Joe from SELKIRK NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
i took the inside door off and took the 2 switches out and replaced them; not too difficult.

Water not draining out of dishwater completely

  • Customer: James from Lecant FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I read everyone else's fixes, which were very helpful but my solution of removing the plastic from the motor shaft was a lot easier than others. I simply used side cutters and made two cuts into that plastic piece and it Fell of. much easier than the person using several Dremmel blades to cut it off.. That was the most difficult phase until I grabbed my ole phone company side cuts and just cut it off in 15 seconds. Thanks for all the other tips. I love dealing with Parts Select, Fast and efficient. Jim W
All Instructions for the RUD5750HB0
151-165 of 165