Models > RUD5750DB3 > Instructions

RUD5750DB3 Roper Dishwasher - Instructions

All installation instructions for RUD5750DB3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750DB3
46-60 of 181
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

leaking suds and water front bottom of door

  • Customer: Wayne from Peru IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

door panels looked old/bad

  • Customer: Gail from Mayville WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Washed the edges good and clean to remove old tape that was holding the old panels. Slid in the new ones and found that the retaining strip would not work without replacing the inner strip. I didn't want to order this $53 dollar plastic strip so I squeezed a couple of rubber pieces into the bottom of the side edges to hold the top panel. Placed the retaining strip in place and used a long strip of black duct tape at this bottom edge to hold it all. It works and the new panels make the dish washer look close to new,the black duct tape hardly shows. This works good for my 10+ year old dishwasher until it is replaced with one that has a better door design.

door seal leak

  • Customer: Tim from Lock Haven PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!

These access panels are just plastic. My son's big 10 foot stepped into it and busted the holder for the screw. This was the 2nd time we had to replace this part in 4 yrs. I was very glad to find it again.

  • Customer: Rheannon from Havre MT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
The easiest way to change this out is to remove the access panel(like the one you purchased) and the metal brace that supports it to the bottom metal access panel. To do this, REMOVE the screws in between the door and access panel. Step 2: LOOSEN screws that connect the metal braces together. You do not need to remove them completely as the middle brace slides up. You should now have the panel and brace together in your hands. Step 3: Using a flat screw driver pry (and I mean pry!) the retainers out of the catch. At this point breaking the old plastic is a better option than bending the metal! Once removed, your ready to swap out the front cover of the panels and put'er back!! Good Luck!

the motor would not run.

  • Customer: gerald from new iberia, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 2 of 2 people found this instruction helpful
i determined that the impeller was not free. ordered and installed an impeller kit which included a new bushing, which was the culprit. it was a fairly simple fix, needing only to remove the pump housing from the back of the motor. access to the impeller was by removing the screw-in, x shaped connection on the back side of the impeller housing. runs like new again. the fix was far less expensive than a new washer.

Inserting Lid Spring

  • Customer: Emile from Jamaica NY
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 11 people found this instruction helpful
Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

The soap dispenser lid was broken

  • Customer: ed from potomac MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

Pump impeller went crooked, apparently both from wear and moving the unit. Would not then stay in place.

  • Customer: Guy from Santa Fe NM
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)

dish washer leaking

  • Customer: Gary from Winnemucca NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 3 people found this instruction helpful
Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

Leak at the seal

  • Customer: Craig from Southern Pines NC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Getting the dishwasher out was easy. Getting to the impeller was easy. Getting the impeller off of the motor shaft was the difficult part. I had to use my Dremel tool with lots of cutoff wheels to cut the impeller off of the motor shaft a little piece at a time. It appeared to be rust on the motor shaft that was causing the impeller to not come off. There is not much room for the Dremel so be careful not to nick the pump housing or cut into the motor shaft. Keep the vacuum close by to clean out the plastic impeller shavings. Clean the rust off the shaft with steel wool, fine sandpaper etc. Assembly was easy once everything was cleaned up.

MY DISHWASHER STARTED LEAKING OUT THE BOTTOM OF THE IMPELLER ASSEMBLY.

  • Customer: John from Eldersburg MD
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 5 of 12 people found this instruction helpful
I WENT ON LINE AND FOUND THE PARTSELECT WEBSITE AND WAS ABLE TO IDENTIFY THE DEFECTIVE PARTS USING THE SCHEMATIC DRAWINGS. I ORDERED THE PARTS AND IN ABOUT AN HOUR I HAD REASSEMBLED THE DISHWASHER AND HAD IT RUNNING AGAIN MUCH TO THE JOY OF MY WIFE AND CHILDREN. (NO MORE WASHING DISHES BY HAND!). i ALSO PURCHASED THE TOUCH-UP PAINT AND TINE TIPS AND NOW THE WASHER LOOKS AND RUNS LIKE IT DID WHEN I PURCHASED IT.

Dishwasher was not pumping out water

  • Customer: Shelley from Florence SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 3 of 6 people found this instruction helpful
My husband did the repair. He sucked the water out with the wet/dry vac. Layed it over on the front and removed the pump motor and replaced it.

Missing front panel

  • Customer: Cristen from Richmond VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 12 people found this instruction helpful
Purchase new filler panel, new outer panel, and gasket to hold panel in place. Secure gasket to dishwasher frame then insert new panels.

Water leaking from pump seal.

  • Customer: Jasper from Opelousas LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 2 of 4 people found this instruction helpful
After getting the pump and motor off of the dishwasher, I used a screwdriver and small hammer to break the impeller off of the motor shaft. The shaft was corroded and pitted real bad but this doesn't matter because the shaft of the impeller actually goes through the seal. I removed the old seal and replaced it, slipped the new impeller back on the motor shaft and put the pump and motor back on the dishwasher. Our local repair man told us it couldn't be repaired and we needed a new dishwasher. I had the parts from Part Select in 2 days. The parts were less than $35 dollars and repair very simple. The person on your comment section on how to fix it that said to break the old impeller off of the shaft made the job very simple.

soap dish door does not always pop open

  • Customer: John from Dubuque IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 7 of 19 people found this instruction helpful
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
All Instructions for the RUD5750DB3
46-60 of 181