Models > RUD4500DB3 > Instructions

RUD4500DB3 Roper Dishwasher - Instructions

All Instructions for the RUD4500DB3
91 - 105 of 168
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
soap dish door does not always pop open
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Parts Used:
Spring, Lid
  • John from Dubuque, IA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
7 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door seal leaked steam
It was a very simple repair. I removed the old door seal out of the track and installed the new seal.
Parts Used:
Dishwasher Door Gasket - Gray
  • BRIAN from GOWANDA, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door leaked
removed old seal, placed new seal in place. Used my fingers to push it in place. It didn't work as it still leaks. I've put vaseline on the seal and door and it helps but still leaks. The dishwasher doesn't overfill, so I still have the problem, just not as bad.
Parts Used:
Dishwasher Door Gasket - Gray
  • Kathy from Chapel Hill, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Soap Lid Pin Broken
Snap the old lid off, remove the pin & spring & install new Pin & Spring. Very easy. Thanks To Parts Select got the right parts.
Parts Used:
Spring, Lid Soap Dispenser Cover Pin (Lid Hinge)
  • Robert from Port Clinton, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
4 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
slow leak at motor/pump interface
Got parts breakdown online, took pump assy apart, ordered new parts, replaced bad parts, put pump assy and dishwasher back together, piece of cake, no problems.
Parts Used:
IMPELLER Disk & Mount Assembly
  • Donald from Webster Groves, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Small leak in bottom right corner of dishwaher
Took off bottom plate (2 screws) and ran unit to ensure where leak is from....it appears to be the door seal. Pulled out old seal with fingers and replaced door seal, ensuring its properly "fitted"..ran unit, no leaks, put bottom plate back on
Parts Used:
Dishwasher Door Gasket - Gray
  • Roger from Duluth, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cap did not stay in the hole any longer.....was melted
Just screwed the new cap in. This PartSelect was AWESOME. So easy. Lighting fast shipping !!!!
Parts Used:
Rinse Aid Cap
  • Debra from York, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking from front door of dishwasher
Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!
Parts Used:
Dishwasher Door Gasket - Gray
  • Gregory from North Port, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
pump seal and impeller
had to replace the insides of a leaky pump
Parts Used:
IMPELLER
  • David from Lisbon, IA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench set
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Seeping From Under/Around The Door
I opened the door and pulled the gasket from around the dishwasher. The gasket does not have any adhesive around it, so it pulled free almost immediately. The new gasket was pressed into place around the door and I was done. It couldn't have been any easier. I suspected it was the gasket when I saw pinched portions that did not return to the original shape and there were no visible cracks in the machine.
Parts Used:
Dishwasher Door Gasket - Gray
  • Nate from Fort Worth, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaked through door gasket.
Lowered door and put a weight on it to keep it open. with screwdriver pried out the old gasket. It was simple. looked at the end of the replacement gasket and inserted it into the track with the small hole down. Job Complete. about three minutes total time.
Parts Used:
Dishwasher Door Gasket - Gray
  • Charles F. from Burnet, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking around door
1-2-3 EASIEST JOB I EVER HAD to DO AND THE WIFE IS PROUD OF ME FINALLY.

THANKS , , ,Bat from WEST SENECA (Buffalo, NY)
Parts Used:
Dishwasher Door Gasket - Gray
  • john a from west seneca, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke one part trying to install
no tools necessary buy instructions would have brrn helpful
Parts Used:
Pin (Lid Hinge)
  • dwight from onaka, SD
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front leak
pulled out the old gasket, aligned and pressed in the new gasket
Parts Used:
Dishwasher Door Gasket - Gray
  • Rod from Dripping Springs, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
seals were leaking,dry rotted from setting five years without using.
I Disconected The 3' hose Behind Impellor.Unscrew Cap Holding Impellor In. Pull It Out, Replce With New One.Put It Back Together In Reverse
Parts Used:
IMPELLER
  • mike from seymour, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RUD4500DB3
91 - 105 of 168
Back to Top