RUD3000HQ0 Roper Dishwasher - Instructions

Removed screws under counter holding washer in place. Pulled washer out until I could access the back. Turned water supply off (in my case faucet under the sink) Turned power off at breaker.
Disconnected water line and electrical wires noting wire location. Removed solenoid unit by undoing two screws on frame. Installed new unit, connected wires and water. Turned water on to ensure no leaks and pushed washer back under counter. Turned power back on and checked machine operation. Replaced the screws under the counter to keep machine in place. This is very easy. In my area a plumber would charge $75 to do this.

The gasket was a breeze, with just pulling out the old one and slowly pushing in the new in the track with my fingers. The shield was a little harder since there was no instructions before me. It turns out that it fits in the inner door and is used as a baffel for the steam (another problem with leaking out the bottom). After removing the front cosmetic pannel you need to thread the shield inside on three tabs that hold it. It took a few times to orientate it properly but it snaps in when correct. After the front pannel was put on and the unit test operated, the washer no longer leaks. Highly recommend the parts and help from PartSelect and the others before me.

Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one full revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.

The dishrack came in one box I opened the box snapped on the rollers and the bumpers and put it in the dishwasher, could not have been easier Thank you partselect

After completely pulling out the dishwasher, I removed the rubber housing that connected to the housing assembly. I unscrewed the retaining ring which holds the impeller in place and then pulled the impeller off the shaft (which took quite a bit of force). I removed the seal seat ring and using the impeller and seal kit I replaced all the internal parts to the impeller system. (note: the impeller and seal kit acutally contained the seal-head and seal seat ring so I was able to return those two parts.) I put all of the disassembled parts back together.

I removed all the ( what my Husband called star screws ) star screws and removed the housing panel ( holds dish detergent cup and silverware basket ) I discovered everything accross the bottom was all gucked up with detergent soap accumulation. I took the part to the kitchen sink and used the sprayer hose on the part with hot water and it cleaned up beautifully, and the detergent latch then worked ( the spring that operates the latch was all gucked up with detergent accumulation ).
I am the wife and did all of this myself and it only took around 5-10 min. My Husband had to help me figure out the type of screws because they turned out to not be phillip screws, but as Hubby called them.."star screws".
Soooo, I did not need to use the Latch Kit I purchased, so will store it in my parts supply! :)
Happy repairs to you..
Judy Estes Park, CO

I pulled off the old clips and easily replaced them with the new clips and popped on the wheels.
I replaced 8 clips and 8 wheels in less than 15mins

replaced the two water defiector's, I had changed the door seal and should have changed the defiectors at the same time. Save yourself some time and ordor both parts. This is a easy fix, anyone can do.

Had to pull the dishwashwer out to replace the latch. Did this by unscrewing the 2 screws that hold the Dishwashwer to the under side of the counter. Dishwasher then pulled out easily. Then unscrewed to screws on the latch. The screws were accessed by pulling out the modling/strip around the dishwasher door. Also easy to replace the screws. But sliding it back in was a little harder. Had to shorten the front legs on the dishwashwer to get the back of the dishwasher to go back in. Then screw the front legs back out. Finally re-inserted the screws under the counter that attached the top of the Dishwasher to the counter top.

There were no instructions with the part, but looking at the old rack it was simple to see how the parts should be assembled. Took the center part from the old rack, twisted off, and applied it to the center of the new rack. Snapped on the wheels and was done. Very simple assembly.

The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?

first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.

I removed the inner nut holding the spray arm onto the pump. Turned the washer on it's back and removed the wire clip holding rear of the pump motor. Completely removed the pump housingand motor from the washer. Removed three(3) long screws holding the motor to the pump housing. Removed the dish from the housing and removed the old impeller and seals .
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.

Sincerely,
James