Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RUD3000HB1 > Instructions

RUD3000HB1 Roper Dishwasher - Instructions

All installation instructions for RUD3000HB1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD3000HB1
76-90 of 166
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Small leak in bottom right corner of dishwaher

  • Customer: Roger from Duluth, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Took off bottom plate (2 screws) and ran unit to ensure where leak is from....it appears to be the door seal. Pulled out old seal with fingers and replaced door seal, ensuring its properly "fitted"..ran unit, no leaks, put bottom plate back on

4 broken wheel assemblies on upper rack

  • Customer: Jeffrey from Little Egg Harbor, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Snapped them in place....2 minutes....ordered the parts 2PM on a friday and they arrived 11AM Saturday...couldn't believe it! Thanks!

Water leaking from front door of dishwasher

  • Customer: Gregory from North Port, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!

door leaked

  • Customer: Kathy from Chapel Hill, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
removed old seal, placed new seal in place. Used my fingers to push it in place. It didn't work as it still leaks. I've put vaseline on the seal and door and it helps but still leaks. The dishwasher doesn't overfill, so I still have the problem, just not as bad.

door seal leaked steam

  • Customer: BRIAN from GOWANDA, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
It was a very simple repair. I removed the old door seal out of the track and installed the new seal.

Dishes would'nt come clean or dry from torn boot

  • Customer: David from Sallisaw, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 12 people found this instruction helpful
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

seals were leaking,dry rotted from setting five years without using.

  • Customer: mike from seymour, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 6 people found this instruction helpful
I Disconected The 3' hose Behind Impellor.Unscrew Cap Holding Impellor In. Pull It Out, Replce With New One.Put It Back Together In Reverse

Tines where falling off old rack

  • Customer: RONALD from EAST GREENWICH, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 12 people found this instruction helpful
The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

slow leak at motor/pump interface

  • Customer: Donald from Webster Groves, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Got parts breakdown online, took pump assy apart, ordered new parts, replaced bad parts, put pump assy and dishwasher back together, piece of cake, no problems.

pump seal and impeller

  • Customer: David from Lisbon, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 1 of 3 people found this instruction helpful
had to replace the insides of a leaky pump

Front door panel was missing

  • Customer: Crystal from Bowman, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I removed the cardboard insert, put the new front panel on and replaced the tabs. That was it!

The door leaked during wash cycle

  • Customer: John from Frankfort, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.
I installed the new gasket. No cleaning was necessary.
It took less than five minutes. It now works like new.
I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.

front leak

  • Customer: Rod from Dripping Springs, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
pulled out the old gasket, aligned and pressed in the new gasket

leaking around door

  • Customer: john a from west seneca, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
1-2-3 EASIEST JOB I EVER HAD to DO AND THE WIFE IS PROUD OF ME FINALLY.

THANKS , , ,Bat from WEST SENECA (Buffalo, NY)

I broke one part trying to install

  • Customer: dwight from onaka, SD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
no tools necessary buy instructions would have brrn helpful
All Instructions for the RUD3000HB1
76-90 of 166