RUD1000DB0 Roper Dishwasher - Instructions

The bottom trim piece popped off easily and I removed the damaged panel and replaced it with the new one. I snapped on the trim piece and I was done. It took less than five minutes.

Watched your video and replaced seal in approx. 5 minutes, probably less. Still leaked so I looked at your page for solutions, found out where the air vent was and pried it open, very disgusting mess. With screw driver and long tweezers dug out what I could then poured a mixture of bleach and water in the vent. Totally cleaned it, very white, vent cover went into a bucket of bleach and hot water and it cleaned very well. Put vent cover back on and did a load of dishes, works fine. Thank you for having such a great website, if I ever need help again I will be back. It's a shame someone didn't tell you about cleaning the air vent when you bought the dishwasher.

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

Pulled out old gasket with needle nosed pliers, cleaned groove, installed new gasket just like the video provided on website. Took less than 10 minutes.

Got on the computer, located your site and read the repair stories.Thought, I can do this. Ordered the impeller and seal kit. I followed the same procedures as your other customers, however, when I turned it on for a test it still leaked. Went out looked for a new dishwasher, for $389.00. After talking to my wife,(been married over 60 years)decided to try one more time. Went through the same steps. Loosen the plastic ring remove The revolving spraying arm, tipped on the front to get to the bottom. mopped up the water,disconected water, electric, and hoses. Pulled the motor and pump unit, disassembled the pump unit,then I realized I had installed the rubber and plastic bearing backwards. The rubber to rubber wore out real fast. Ordered a new seal kit (no impeller) Put it all back together and it works just like it did 19 years ago. Total cost less than $60.00. It is a good feeling when your able to fix somthing like this, especially ehen your a fat 83 year old. I would like to meet the person that changed this in a half hour.

pulled out the old seal and put in the new, fixed the leak!

Watched the video and did the repair it was easy.

Took out old dishwasher rack and replaced with new.

The hardest part was locating the leak. After consulting the other repair suggestions, I concluded that the gasket was a little more worn on one side than the other so I ordered the gasket. The evening before the gasket arrived (quick delivery from partselect.com) I decided to shim out the old gasket with some old door insulation. It made the door harder to close but it didn't leak any more. When the gasket arrived I replaced the old with the new. It leaked more than ever. After reading more repair instructions, I decided to take apart the door vent and check it. It was packed solid with gunk. After a good cleaning, I put everything back together. No leaks! I tried every repair listed except the door vent. Guess steam is a good gunk conduit LOL. I supposed I didn't really need the new door gasket but I can tell the door has a tighter seal now. Here's a tip to watch for. If the door doesn't leak right away after the washer starts, take the door apart and look at the vent. It can look just fine from the outside and that's deceiving. Someone else mentioned the 'leak' timing that finally got my attention and lead to the 'fix.'

I watched the video that you had on line and the repair was done in a snap. The shipping was fast also.

Trial and error. The spring was difficult to install, the pin and door were easy.

This was stupidly easy! I found Parts Select from a Google search on making the repair. That took me to a YouTube video that Parts Select had posted on how to repair. I followed the instructions and it was fixed in 10 minutes and that was only because I took my time. I ordered the part online from a link on YouTube and I had it in two days............. Unbelievable!!!!

I paid a repairman over $100 to tell me he could find nothing wrong with my leaking dishwasher (it didn't leak when he ran it). I narrowed down the problem to a missing water deflector, but decided to replace the door gasket as well. It took less than 5 minutes to do the job. The only tool I used was a pair of needle-nose pliers to grasp the old door gasket and get it coming out of the groove. Thanks PARTSELECT for super-fast shipping and a website that is easy to navigate. I'll be coming back, 'cause all of my appliances are getting some age on them!

The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.