Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RT20CKXXW01

RT20CKXXW01 Roper Refrigerator - Overview

Get Parts and Repair Help for RT20CKXXW01

If you know the refrigerator repair part you need, you can browse the list of all parts on the RT20CKXXW01, or you can search by name or part description. You can also find your part by where it is located on the RT20CKXXW01 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for RT20CKXXW01 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$40.25

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forced-air cooling for the condenser coil.

$10.19

Door Shelf End Cap Set

This door shelf end cap set contains two white end caps. Each end cap can be used as either the right or the left side. These end caps also come with adhesive strips and an instruc...

$62.75

Evaporator Fan Motor Kit

The evaporator is found in the back of the freezer. This kit comes with two mounting grommets, two sleeves (not to be used on porcelain models), two #8 mounting screws, and a push-on fan blade.

$27.50

Shelf Support Stud

This is a 12 piece kit.

$13.23

Door Shelf End Cap Set

This door shelf end cap set contains two white end caps and adhesive tape.

$7.20

Touch-Up Paint - White

18ml

$35.17

Light Socket Kit

The bulb is sold separately.

$88.48

Add-On Icemaker Assembly

This icemaker kit comes with a flat plug, wiring harness, fill tube, water inlet valve, ice bin, mounting hardware, and instructions.

$11.07

Spray Paint - 12 oz. - White

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The frost free feature of the freezer was freezing over with ice and cooling coils were being insulated with thickening frost which caused the cooling air to rise in temperature from -5 degrees to 20 degrees.

  • Customer: Lawrence from Grahamsville, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 324 of 380 people found this instruction helpful
I troubleshot the problem by reading the electrical schematic and concluding the heating elements (defrost cables) were either defective or the bi-metal temp sensor was open. When closed the temp sensor completes the circuit for the current to flow through the heaters to defrost the cooling coils every 8 hours and then when the bimetal opens at 55 degrees t... read more

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 175 of 195 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 124 of 132 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more