Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RT20AKXZW01

RT20AKXZW01 Roper Refrigerator - Overview

Get Parts and Repair Help for RT20AKXZW01

If you know the refrigerator repair part you need, you can browse the list of all parts on the RT20AKXZW01, or you can search by name or part description. You can also find your part by where it is located on the RT20AKXZW01 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for RT20AKXZW01 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for RT20AKXZW01

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$3.02

Screw

This screw is sold individually.

$47.35

Capacitor

This capacitor is also known as a run capacitor, and it is most often used in refrigerators and freezers. This part provides the voltage or energy current required to start the com...

$5.21

Icemaker Water Fill Tube Kit

The icemaker water fill tube provides water to the icemaker so it can produce ice and dispense water. If you notice that your ice maker is not making or dispensing ice, or is leaking, you may need to replace the water fill tube. This water fill tube kit comes with a fill tube and a compression nut. This part is made of white plastic and is approximately 10 inches in length. The ice maker water fill tube is in the rear of the fridge. To complete this repair, you will need a 1/4 inch nut driver and a utility knife. Before beginning this repair, you may want to disconnect the water and power supply to the refrigerator.

$7.74

Door Shelf End Cap Set

This door shelf end cap set contains two white end caps. Each end cap can be used as either the right or the left side. These end caps also come with adhesive strips and an instruc...

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant before it enters the evaporator. When your fan or fan motor is not working your refrigerator will not cool properly. This is a 2-Watt, 115 Volt motor that rotates the fan in a counter clockwise direction. This kit includes the hardware needed for installation, and a set of instructions. Before you begin any repair work make sure to unplug your appliance.

$20.01

Bimetal Defrost Thermostat

This clip-on thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$25.52

Shelf Support Stud

This is a 12 piece kit.

$12.83

Door Shelf End Cap Set

This door shelf end cap set contains two white end caps and adhesive tape.

$57.48

Evaporator Fan Motor Kit

The evaporator is found in the back of the freezer. This kit comes with two mounting grommets, two sleeves (not to be used on porcelain models), two #8 mounting screws, and a push-on fan blade. If you are experiencing symptoms such as the fridge making loud noises (generally stemming from the freezer compartment), or the fridge/freezer feeling warm in temperature, this may indicate a need to replace your evaporator fan motor. This part pulls air into the evaporator coils and then disperses the air in a continuous motion throughout the refrigerator and freezer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 221 of 245 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 133 of 143 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 112 of 123 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more