Models > RT18BKXKQ03 > Instructions

RT18BKXKQ03 Roper Refrigerator - Instructions

All installation instructions for RT18BKXKQ03 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RT18BKXKQ03
16-30 of 149
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fridge wont defrost

  • Customer: james from Mcdonough GA
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 13 of 23 people found this instruction helpful
Freezer freezes and wont defrost. Ice clogs up the coils and the fridge gets hot. Repairman said it was the timer so I replaced that and it didnt fix it. Ordered defrost heater and installed and it is still not fixed. 150$ so far. Should have thrown it away like the repairman suggested.

socket melted with bulb in it.

  • Customer: martin l. from JACKSONVILLE, IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 10 people found this instruction helpful
plastic warped in ,spaced out and, the socket snapped back in place.

The freezer section was working fine. Not properly cooling the refrigerator

  • Customer: Donald from Waco TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
I looked on line to see what was causes of the problem and determined that it was probably the fan in the freezer not working. I took the back section of the freezer apart and saw the fan was not running. I checked the parts on line and found that it was availiable and ordered a new fan motor. The blade looked fine, but I ordered a grommet anyway to ensure that there was no vibration problems causing the fan motor to go out. When the fan motor arrived, I began disconnecting the old one after unpluging the refridgerator and noting the terminals for the wires. The wire terminals were in a slightly different location, but reasoned out which wire belonged to the correct location. I pulled the old fan motor out, switched out the fan blade and grommet and re-incerted the new fan motor. I reconnected the wires and re-assembled the rear wall of the freezer. I plugged in the refridgerator and wa-la! It worked.

would not defrost and would not get cold.

  • Customer: Jack from Beardstown IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Had alot of frost build up, coils were frozen solid. Removed the coil cover to defrost.
Ordered the defrost timer on friday, arrived on saturday. only took 15 minutes to install. Working great

door handle broke off

  • Customer: Debbie from Eagle CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
It would have been nice to know that screws were not included and/or show were screws could be purchased. Thank goodness I was able to reuse the top 2 and had an extra screw in my tool bag that fit the bottom, because the existing screw had been super glued into bottom part of handle.

Freezer Frosting

  • Customer: David from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 8 of 12 people found this instruction helpful
My problem was that the freezer was frosting up.
I have a no frost system so I decided to investigate.
I removed the panels inside the freezer compartment.
This took me about 5 minutes. After the ice had melted, I noticed that the clicks-on (bi-metal stat)
has the top push out at about a 45% angle.
After ordering a replacement, I pushed the top of the bi-metal down to where it's supposed to be.
Put the freezer back together and plugged it in. I needed the freezer while the part is being shipped.
The part arrived in about 3 days, which was very fast and a surprise to me.
The freezer was still working fine so I put the part in the drawer until I needed it.
That was in April 09 and it is still working. I have the part in case I need it.
I am very happy with the service I received from PartSelect and will recommend them to everyone.
David Daley

evaporator iced up every 5 days or so

  • Customer: nicholas from riverside CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 7 of 11 people found this instruction helpful
Very easy, unscrewed control panel cover (1 screw) which is located under the freezer compartment inside the refrigerator. Took out non working defrost timer installed new one replaced cover, done. Total time: less than 5 minutes.

light inside fridge was flickering and clicking

  • Customer: bill from escondido CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 9 people found this instruction helpful
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Damaged door trim in fridge. ( Rental)

  • Customer: Bob from Madison IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
Slid out old ones and installed new ones

the ice maker quit producing ice.

  • Customer: darryl from little york IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 4 people found this instruction helpful
I removed 1 bottom screw and 2 upper screws useing a 1/4 inch socket nut driver. then useing a flat edge screwdriver i incerted in slot to remove wiring cluster. to install just reverse process. you maye have to cut u-shape slot for water spout to sit in.

Broken gooseneck on fill tube

  • Customer: Thomas from Brunswick OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
The gooseneck on the icemaker fill tube extends out beyond the back cabinet of the refrigerator, and is easily broken. Luckily, this part is a piece of cake to replace. You'll literally spend more time pulling out your fridge and cleaning out behind it then you will replacing this part.

Shut off water supply line, and turn off ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.

Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.

Refrigerator door hinge screw missing

  • Customer: William from Manchester TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set, Wrench set
  • 5 of 7 people found this instruction helpful
Lost screw on bottom refrigerator door hinge which allowed the door to fall off. Purchased screw from Part Select for the Roper refrigerator. Drawings and parts list for this unit were available on their website. Easy repair.

The refrigerator leaked water every time the ice maker filled.

  • Customer: Robert E. from Darien IL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
The problem was discovered to be a cracked fill tube head, This part extends behind the refigerator and is VERY vulnerable to breakage when the box is pushed backagainst a wall space! Placing a shim under the vertical part of the fill tube fixed the problem even without replacing it with the new part. So, now I have a spare!

compressor didnt turn on

  • Customer: gerardo from el monte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 13 people found this instruction helpful
changed the starter connected to the compressor

The Freezer defrosted and everything on the top and the bottom spoiled

  • Customer: Jorge from Miami FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.
All Instructions for the RT18BKXKQ03
16-30 of 149