RT18BKXJW00 Roper Refrigerator - Instructions

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

The repair was very easy, unplug ref. open freezer door, and remove base plate, then remove screws on back plate. I had to tilt top of back plate to remove from freezer. This gives you access to the evap. fan Pull of the three wires, and remove screws from fan bracket, which bolts to the back of ref. Remove fan motor from bracket (2) screws, remove motor, and put replacement motor on bracket, pull fan blade off old unit and push on new motor shaft. Reverse the installation, and you are done. Pretty easy.

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Viewed the viedo - it showed what to do

1. Turn thermostat down to ensure cooling cycle turns on. Open freezer compartment and listen for air flow/fan. If no air flow or fan, but compressor seems to be working, then proceed to next steps. 2. Turn thermostat up to shut off refrigerator cooling cycle. 3. Open freezer and remove wire shelf (if installed). 4. Using nutdriver or socket set, remove screws securing metal panel on the back wall of the freezer interior. 5. Pull metal panel out to expose evaporator fan and evaporator coil. 6. Ensuring area around fan is clear, turn thermostat down to again start cooling cycle and check if fan operates - if not, then fan needs to be replaced. 7. Turn off refrigerator and unplug from electrical outlet. 8. Order replacement fan (unless you happen to keep one in stock). 9. Remove two screws securing fan and fan bracket assembly to back wall of freezer, note wire connections to fan (red, white and green), disconnect wires and remove fan assembly. 10. Gently pull off fan blade, it is a compression fitting. 11. Remove two screws holding back and front fan brackets together and remove fan motor. 12. Remove rubber gasket from front and back of old motor and insert then on the new replacement fan motor (these rubber gaskets align to openings in the fan brackets, thereby holding the motor in place when installed back into the brackets). 13. Reinstall fan brackets onto new motor matching how the old motor was assembled. 14. Press the fan blade onto the new motor shaft. 15. Reinstall fan motor assembly onto back wall of freezer. 16. Reconnect wires to new motor as they were previously connected to old motor. 17. Reinstall back wall metal panel that covers the fan motor assembly and evaporator coil. 18. Reinstall wire shelf (if applicable). 19. Plug refrigerator in and adjust thermostat to normal setting to initiate cooling cycle. 20. Open freezer and listen for fan and airflow, if you hear it operating correctly, then close freezer and refrigerator and confirm temperatures after refrigerator has cycled through one full cooling cycle - adjust thermostat as necessary. 21. Tell your spouse or significant other that for less than fifty dollars you just saved the price of replacing the refrigerator.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

Verified the defrost time and heating element were good and ordered parts. Parts were delivered way before I thought they would!! thank you PartSelect!! Had inside of freezer already apart, it takes a 5/8 driver to remove the three screws that hold the bottom plate and back cover. Then it's 2 clips that hold the front of the bottom plate, I used a small flat bladed screw driver to pull those up. The harness has several plugs and every thing is color coded (very easy to match which plug goes where). Un-clipped temp switch and plugged harness back in, re-assembled in side of freezer and plugged it back in, easy as can be.

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.

I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.