RT14GDXBW00 Roper Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The end pieces for the refrigerator door broke
The repair was so easy. All I had to do was take out the screws, and fit the new pieces in. Even though the new pieces were chrome plated plastic (unlike the original metal black ones) you can't tell that they didn't come that way. It makes the refrigerator almost look brand new! When we move out our landlords will definitely have received an upgrade!
Parts Used:
-
Jaclyn from Pleasant Grove, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket was splitting
Had to remove both doors freezer and fresh section. Once I had door off removed the screws, and old gasket, cleaned all aroud where old gasket was, and proceeded to put new gasket on, It was hard lining up gasket with metal rods that hold gasket on could only do one screw at a time, because gasket kept slipping out, it was very time consuming.
Parts Used:
-
Lawrence from Tishomingo, OK
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Socket set
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old tube had cracked due to being frozen....
I followed the simple steps outlines in the great video! Thanks
Parts Used:
-
Stephen from Greensboro, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Coating on ice maker coming off in ice.
Because of the age of the unit, I replaced all but the wire harness. It was easy to repalce.
Parts Used:
-
Kelly from Taylorsville, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
End Cap cracked and broke from age.
Removed the one screw and replaced with new end cap. Only disappointment was the beige color, as I would have preferred a white one. White color was not offered. Other than that it took less than five minutes. I'd rate it 4 stars.
Parts Used:
-
Bonnie J from Nottingham, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
19 year old light switch broke
Great service. Unpluged old switch and pluged in new one. Works great
Parts Used:
-
Fred from Watertown, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The fill tube froze and cracked
It was easy and quick to find the part that I needed, order it and have it shipped. The fill tube arived in 3 days and was easy to replace.
Parts Used:
-
Phillip from Sellersburg, IN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Wrench (Adjustable)
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part broke.
-
Felix A from Orlando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking onto the floor
After finding water on the floor I investigated to find the leak. I Found theat the Icemaker fill tube on the back of the frig was cracked(due to someone pushing the frig back against the wall). Turned off the water supply to the icemaker. Removed the 2 screws holding the tube in place. Slid the tube out and slid the new one in. Replaced the screws and turned the water back on. Very easy, very inexpensive.
Parts Used:
-
Dean from Sheboygan, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light would work intermitently
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Parts Used:
-
Gregory from middle island, NY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old switch left freezer bulb always-on
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Parts Used:
-
JONATHAN from ELKINS PARK, PA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace Bad Switch
Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place
Parts Used:
-
carlos from haverstraw, NY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken light switch
Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.
Parts Used:
-
George from North Scituate, RI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lights didn't always come on when was opened
Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.
Parts Used:
-
Gary from Jenkintown, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light staying on
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Parts Used:
-
Cecelia from Beaver Dam, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!