RT14BKXKQ02 Roper Refrigerator - Instructions

Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The black wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.

Used angle screwdriver to tighten.

My fridge is a little different from the video model. The Controls in the fridge are located on an "arm" which swings down when the two screws are removed from the sides. It was not necessary to remove a front plate or knobs. However, I found when I got in to it that the old timer was not held by screws, but by plstic posts which had these "speed nuts" on them. This is a little metal plate which fits over the plastic post and bends to lock it in place. When you try to remove it, it acts like a barb, holding the little sucker on. I ended up bending the ends of those little suckers up tight against the post and twisting and pulling with needle-nose pliers. I broke one post like others before me commented, but one stayed intact. The only break at the top, so there ie still post left to hold the new timer. Once it was off, I was able to replace easily. The directions for choosing the right prong were a little confusing, but follow your gut and go with the wire colors. My schematic found in the bottom of the fridge did not look like any of the drawings, but I could match the wire colors. I also asked "Just Ask" for help, to make sure. My gut instinct was right. My fridge is now working again beautifully. If a housewife with no appliance repair knowledge can do it, so can you. I fixed my dryer with PartSelect too!I will never call another repair man until I have checked this site to see if I can do it myself. Bet I have saved $600 so far at least!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

I found the evapoator iced over and the evaporator fan not working . I tested for voltage on the fan circuits ,found them to be good .ordered the part i needed and repaired the fridge . in the meantime until i recieved my part i put a small fan in the freezer to keep the evaporator form icing over so my food would not spoil .

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks

I followed the instructions in the video on the PartSelect website. The only problem I ran into was that I couldn't switch the grounding tab connector from the original side of the motor to the other. I had to add more wire so that I could reach it in its new location.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I did the repair just as your video showed me. It worked out great.

1. I removed the plastic back cover panel in the freezer. 2. Took flash photos with my phone of the motor and wire configuration. 3. Removed noisy Evaporator fan bracket from freezer. 4. Removed Fan Blade from old Motor. 5. Removed old Motor from Bracket. 6. Installed New Motor into the bracket. 7. Installed the fan blade onto motor spindle. 8. Installed the bracket onto the back wall of freezer. 9. Noticed that the tab for the ground wire was inaccessible. 10. Cursed like Linda Blair in the Exorcist for about 5 minutes. 11. Repeated steps 3 - 5... 12. Unscrewed the ground tab and placed it on the opposite side and screwed it back in. 13. Repeated steps 6 & 7.... 14. Tried to install the bracket and motor back onto the freezer but the bracket screw holes weren't lining up. When I removed the motor to flip the ground tab over, I reinstalled the motor onto the bracket upside down. 15. Tear some hair out of my head. 16. Repeated steps 4 & 5 and flipped bracket over. 17. Repeated steps 6 - 8... 18. Placed wires onto tabs. 19. Ground wire would not stay securely onto the tab. 20. Slightly opened up metal fastener of ground wire with needle nose pliers and stuck it onto the tab. 21. Still not on there super tight. I gave up wrestling with it and just prayed it will stay on there anyway. 23. Turned on freezer to check if it works. 24. Reinstalled plastic back plate. 25. Put melted food back into freezer.

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.