Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plasticware melted onto burner
I removed the screw holding the tilt mechanism to the range top. Removed the clips holding the block together. Disconnected the two power leads on the old burner and replaced with the new burner. Closed the block around the leads. Screwed the tilt mechanism back to the range top and that was it!
Easiest thing I've done. Shut off breaker. Unplug range. Pull out from wall (because this is a good time to remove the back, clean under and around the unit, check out the insulation and electrical contacts....or skip it, whatever). Open oven. Remove door (while ajar, pull up). Remove racks. Unscrew mounting plate from back interior wall. Set screws aside. Gently pull element forward until the leads and wires come through the insulation. Remove any strands of insulation that stuck to the leads and connectors. Unscrew leads. Keep left wire to the left and right wire to the right. DO NOT CROSS. Set screws aside. Discard old element. (This is a good time to clean your oven, if you haven't in a while.) If you cleaned oven, wait until dry. Position new element, feet down, in bottom of oven. Position left wire on left connector. Screw tightly BUT DO NOT BEND LEAD. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Position right wire on right connector. Screw tightly BUT DO NOT BEND. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Do not leave screws loose. Connection must be tight. Fire hazard, otherwise. If you bent nothing, then gently push element back through insulation until mounting plate is flush. Screw into position. Replace racks. Replace door. If you decide to check insulation and other leads, now is the time. I checked mine and it's a good thing I did.... Unscrew back plate of oven, keeping screws in order. Remove plate. Check that your new element and insulation aren't bunched up or otherwise in a hazardous state. You may notice burned or greasy insulation. You may see burned leads on light receptacle and broil element. If you do, then replace them, too. When finished with everything, replace back plate. Put range back into position, ensuring level and plumb. Plug in. Turn on breaker. Pat yourself on the back. You just saved $100-$250, depending on where you live.
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel 2) Slide out Range from wall 3) Unplug Range 4) Remove back panel and unplug electrical connections to socket 5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb 6) Remove old socket from mounting flange and discard. 7) Place new socket into mounting flange 8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back. 9) Screw in new light bulb from front 10) Replace existing glass cover over new light bulb and snap wire holder in place 11) Replace back panel 11) Plug in range 12) Slide range back to original position 13) Turn on power Works like a charm! Thanks for having the parts after 30 years!
Old infinite switch WB21X36771 broke...heating element stopped heating
1. Bought replacement part said to replace old switch. 2. Pulled old switch out. 3. Replacement part did not match. Would have to take entire switch panel apart to change to this part. 4. Multiple-part instructions very poor. For my switch unreadable. 5. Old part was "push to turn". New part was not. 6. Knob did not fit new switch. Old shaft was "D" shaped. New is square. 7. Gave up. Need to call repair shop. 8. Hope this helps.
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
burner would not lay flat against surface of range.
Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.
Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.
Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.
I simply took the 3 new timer knobs and slid them on the metal shafts. It took less than 5 minutes to replace all 3 knobs. Now I can set the start, stop and time functions which have been inoperable for over 5 years. An easy and straight forward .