RS22BRXDW00 Roper Refrigerator - Instructions

Package came in two days.I opened the box ,took the old draw out and slid the new draw in. Fixed in less than two minutes.I would definitely order from Parts Select again. Thanks for the prompt service

First, although I was SURE I knew what to do, I watched the repair video. I used needle nose pliers to push broken support into wall since I could not pull it out. Selected correct wall fixture, spread holder pins, and snapped into wall opening. Couldn't have been easier!!! Very useful site.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

I took the upper three screws pull the door up and then removed the broker part in the bottom of door by removing one screw. Install new part and put door back securing it by the three screws on the top of regrigerator. Very easy

Easy job due to great instruction video by PartSelect.

I took out the old drawer and inserted the new drawer in the same place! I wish all of life were that easy!

Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

Removed three screws. Discount wire harness. Reverse proceedure for installation.

Watch the u-tube video first ,Then read instructions that came with new unit ! so darn easy. unplug fridge, remove ice bin, clean and dry bin before putting back in service! stick flashlight in freezer loosen 2 top screws remove 1 bottom screw, unmount unit, unplug wire harness, remove icemaker and put on table, close freezer door !! , Remove sensor arm from old unit in down position and install in new unit. plug in new unit and reattach in freezer. replace ice bin and plug in fridge, that's it!, It took about 2 hours for the icemaker thermostat to say OK lets go had a load of ice in aprox 3 hours from finish. piece of cake. Jon

Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

Before I ordered, I followed the great video to disassemble the unit. That's when I realized I only needed to buy the drum. Five days later, I had the part. I thought I remembered how to reassemble it, but I ended up needing to watch the video again. It wasn't difficult, but you must get all the bits back in the same order!! Once that was dine, it all went together easily. Thank you! I'm so impressed with this site that I posted on Facebook about it so my friends can also save big bucks doing simple repairs themselves.

Open fridge....empty old drawer....through out old stuff....remove broken drawer and take downstairs to trash bin. Remove new drawer from package....open fridge. Insert new drawer. Restock with remaining items. Have a cold drink and congratulate yourself for a job well done!!!

The replacement ice maker came with a few different wiring harnesses which I assumed one of them would fit. well none of them did. I took the wiring off of the old one and matched up all of the receptacles and hoped for the best. It worked. The hardest part of the repair was dislodging the ice machine from the massive chunk of ice that had developed due to the leak in the old one. after that it was pretty easy. I hemmed and hawed about the wiring harness for a few minutes but felt confident it was going to be okay. I took the heat shield off of the old one and put it on the new one and used the control cover and the control arm from the old one too. I checked that all the holes and mounting assemblies matched up. I plugged in the wiring harness to the ice maker and than to the refridgerator, used a nut driver to secure it to the inside wall of the freezer with 3 screws, replaced the ice bucket and the cold air diverter and closed the door. Within an hour I heard the first ice hit the bottom of the bucket.

Took out the broken drawer and replaced it with the new one. No problem at all.

The unit was old so I opted to buy a new one even though it was just the motor. It took about 10 minutes to remove it after locating the fasteners, possibly less and about the same to install the new one. When the unit is turned on for the first time it does not start up right away. It will not start until it senses that it is cold enough in the freezer. For me that was about an hour to an hour and a half. There was a note on the cover that this could be as long as thirty six (36) hours. So don't be alarmed when it does not start running right away. The instructions were accurate.