RS22AWXAW00 Roper Refrigerator - Instructions

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

Removed the old one. The new one had a power chord attached but it did not connect to the wire in the freezer. I saw it could be unplugged from the new ice maker and the power chord from the freezer plugged right in. Once installed, was not sure it worked but after a few hours it filled with water and started making ice. Works great now.

I followed the instructions shown in the on-line video for replacing the thermostate control. I had difficulty freeing the capilary tube from around the mechanical lever that controls the freezer side vent opening. I had to remove a screw that held the vent lever in place. This is a delicate activity. I was not happy with the way the on-line video delt with this particular issue. Otherwise, the video was right on and straight forward. The problem is fixed.

Removed correct part from those provided and slipped it into position. No tools necessary.

I followed the instructions on the repair video, fridge is working fine now. Thanks!

I have a side by side so the space to work in was limited but I still completed the install in about 30 minutes. Unplugged the refrigerator then loosened the top two screws took out the bottom screw lifted the ice maker out just far enough to disconnect the power cord reversed the procedure. plugged it back in started making ice in 30 minutes. Probably would have not have taken that long my MS slowed me down a little. The repair man was going to be $300.00 plus $$75.00 trip charge what I paid was $128.41 that was with 3 day shipping.

Turned off the water to the ice maker; disconnected the wiring harness to the ice maker; unscrewed it from the freezer (two screws). Unhooked the ice lever bar, opened up the motor assembly. Switch the motor out (two screws). Installed in reverse order.

Pulled out the icemaker. Switched out the Motor Assembly (so easy) and woke up the next morning with ice. Our ice dispenser wasn't working either. This repair inspired me to take the ice dispenser apart and I found that the lever arm wasn't touching the contact when pressed. We now have ice and a working ice despenser. Oh yeah--my wife was so impressed. The part came in on time and it was very very easy to replace.

unplug frig, didnt turn off water used cord light to see. Took 1/4 nutdriver and loosen screws removed screw on bottom bracket uplugged ice maker. reversed the process for the new one and done

Watched the video link from the part order and the step by step instructions were as easy as the repair man showed. This is an easy do it yourself job that will fix the problem I describe with the unit. Ahhh a working freezer making and keeping ice once again.

The disassembling and replacing the broken part went exactly as the directions.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Followed the example on the video and everything fit in place without any problems. Only issue is that on a double door fridge the freezer is rather narrow so there isn't much room to work making it was a bit difficult to access the mounting screws.

followed video instructions... only thing done differently was to tape crusher blades together before removing from shaft and added a drop of sewing machine oil to all screw sockets before replacing to reduce rusting and create greater ease of removal if further repairs needed

Really couldn't be easier. Loosen 3 screws that are easy to find. Disconnect the quick connect wiring harness. Now you have the old unit out. Take out the wire that tells if there is too much ice from the old unit and put it on the new one ( this was the hardest part of the project) Hook up the new wiring connector and hook it on the screws and tighten it up. Viola, your done. No messing with the water. Took me 5 minutes and I've never done it before.