RS22AQXGW02 Roper Refrigerator - Instructions

1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

My husband and I followed the instructional video on how to replace the "direct drive drum". We took note of how everything looked prior to dismantling the ice bin. We made sure we had the proper tools and a large flat surface to work on and started taking out the screws. Replaced the new drive drum part and put it all back together. The whole process took approximately 30 minutes and the ice crusher works great now. I'm a happy camper!!

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

I watched the ice maker installation video and I installed the new ice maker with no problem and was done in less the 30 min. with everything. The ice maker is working great. thank you Fred

Door cams were worn out. Removed food from door. Removed top hinge cover and hinge. Lifted door off lower hinge pin and placed door on a table. Removed old door cam and installed new one. Replaced closing cam on lower hinge. Set door back on lower hinge and closed door (magnetic strips hold the door in place). Reinstalled top hinge and replaced cover.

I receved the new ice maker and the only problem I had was getting the old ice maker plug disconected from the frig.

Followed the DYI Video provided by partselect. Best advice, take a digital pic prior to disasembly, which of course I didn't! My cordless screw driver w/o the tip, is the same size as the screws thus no need for a nut driver.

I had two repair problems. #1- Ice door kit & #2 control bracket. I followed the instructional video and completed repair in under 30 minutes. I surprised myself and had a happy wife.

First I read your trouble shooting guide and determanded it was the ice maker. Then I watched your repair video which was very helpfull. I ordered the new icemaker, When it arrived I installed per video using only a 1/4 inch nut driver. IT was esay. New ice maker works great.Thank You for the information you have online and the parts and service.

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

Easy.... Video made replacment very smooth. I only needed one tool a nuy driver.

I saw a video of it, and simply took apart the ice maker and put the new Auger Drum in, then reassembled the ice maker.