RS22AQXFW01 Roper Refrigerator - Instructions

1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

My husband and I followed the instructional video on how to replace the "direct drive drum". We took note of how everything looked prior to dismantling the ice bin. We made sure we had the proper tools and a large flat surface to work on and started taking out the screws. Replaced the new drive drum part and put it all back together. The whole process took approximately 30 minutes and the ice crusher works great now. I'm a happy camper!!

Unplugged it for a day listened to the ice melting on the inside and plug it in again. Decreased the temperature settings and it now seems to work fine. I will save the part in case I ever need it in the future.

On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.

I watched the ice maker installation video and I installed the new ice maker with no problem and was done in less the 30 min. with everything. The ice maker is working great. thank you Fred

Ordered part over the phone and received it two days later.....excellent service

Just inserted new drawer and grille. the best part was easy it was to use this website and the order arrived in two days.

I receved the new ice maker and the only problem I had was getting the old ice maker plug disconected from the frig.

I had a problem with my ice dispenser not dispensing ice. The water worked fine but the ice side didn’t dispense ice. I watch the video on Parts Select.com and it was very helpful, but my model didn’t have screws to remove the front cover. At the bottom of the front cover was two indention where you could put a small tool and pry on it, I had to take a small pick tool and pry up on the front cover to pop it loose. You have to take something small like a pick tool because if you use something like a screwdriver or a butter knife you will get behind the plastic housing (also called a hood) that is screwed to the refrigerator. The key is to remove the face plate from the plastic hood piece (that is screwed to the refrigerator), so you have to get in between the face plate and the plastic housing. If you get behind the plastic housing you can break the housing, you must get between the two pieces and it will pop loose. This is the only problem I had with this installation. The rest of the repair was very easy and now my ice maker dispenses ice great.

Took old one out put new one in and its like new! Costs for a simple drawer was $75! Expensive but the transaction was simple!

I watched the installation video on "Parts Select". Unfortunately I watched it twice b/c the first part ordered last October only lasted 4 months. This part seems to be alright as the refrigerator has been running for approximately 6 days now - so far so good.

took out the old one and replaced with new. PERFECT FIT.

I was able to verify that the water inlet valve was ok based on shorting the test points as described in the online ice maker troubleshooting guide. I then ordered the replacement ice maker and received it within 3 days. The repairs went very smooth, remove 3 screws, unplug connector, transfer shutoff wire to new unit, connect power, replace 3 screws. Done. Ice bucket was full within 24 hours.