RS20CKXWW00 Roper Refrigerator - Instructions

Working from inside out . Remove left upper tube cover and then vent cover . Remove thermostat tube from around the vent . Remove knobs and front cover . Remove 4 hex screws , drop the whole unit enough to expose the left control rod , remove the rod retaining clip . Gently separate control rod from unit . Take the whole unit to working bench or table . Remove thermostat and bracket . Need to reuse bracket with new thermostat . Don't forget the clear plastic tube you have to reuse that as well . Be careful not to kink the thermostat tube . Reverse procedure , working from outside in . Good luck

I followed the video instructions, which were wonderful! Thank you for that. I removed the shelves, then turned each stud counterclockwise a quarter of a turn and worked them out. I would have been able to finish in 15 min. Or less, but one of the studs crumbled, leaving only the wire; so I grabbed the wire with the pliers and was able to work the old stud out after several minutes. I placed the new studs into the holes and turned them clockwise until they snapped in place. What a quick and easy fix!

After watching the convenient movie, the replacment of the Thermostat was very simple and easy. i woul strongly advise you to take a picture of the wires before disconecting so, you will be sure to to reconetc it again.The replacment was a success and the refrigerator has been working since them

My wife removed the broken Grille and replaced it with new Grille without using any tools. She was aware of how to remove and replace the grille as she has done it over the years when cleaning under the refrigerator.

I removed the old broken shelves and replaced the ends that were damaged. It took about 5-10 min.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

the online video on how to change out the part saved me tons of time and do it right.....keep those videos coming, also right part too and easy to find on your site

I watched the installation video on "Parts Select". Unfortunately I watched it twice b/c the first part ordered last October only lasted 4 months. This part seems to be alright as the refrigerator has been running for approximately 6 days now - so far so good.

I followed the instructions that came with the part. Less than five minutes it was good as new.

I watched the video on you tube and followed his instructions. It was very easy, it took about 20 minutes from start to finish.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.

Replace ice maker

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

the speed of part delivery was amazing. using the instructions, posted on your web site, the installation was quite easy. without the instructions it would have taken much longer. thanks to all.