RS20AKXDW00 Roper Refrigerator - Instructions

took out the old one and replaced with new. PERFECT FIT.

First I used some glue to stop the crack from spreading, and that worked for a while, but then I deceided to get a new replacement part. What I got was better than the original one as it had a white protective piece over the end of the drawer and I believe that will give more protection to the drawer. My kids did not always close the drawer all the ways and that is how the crack started. So now the refrigerator looks like new again.

I followed the instructions that came with the part. Less than five minutes it was good as new.

I watched the video on you tube and followed his instructions. It was very easy, it took about 20 minutes from start to finish.

just removed tho old one and inserted the new one job complete.

Push it in to place very easy.

Removed old crisper tray and inserted new crisper.jod done

I opened the refrigerator door, being careful to leave the freezer door closed. After verifying that refrigerator light was on, I squatted down to be at the same level as the crisper drawer. Firmly grasping the old crisper drawer by the convenient built-in handle, I pulled the drawer until it was fully opened. I removed the contents of the old crisper drawer, noting the original location of each item, so that I can place the contents into the replacement drawer in the same place. Grasping the old crisper drawer, I pulled outward and lifted slightly until the drawer was off the track and out of the refrigerator. Using both hands, I placed the rear of the new crisper drawer against the drawer track, lining the tabs on either side so that they would enter the track. I applied gentle, rearward pressure, guiding the new crisper door onto the track. This step was a little tricky. I had to wiggle the new crisper door up and down a bit, to get the new crisper door past the "stop bumps" in the track. After the new crisper door was sufficiently in the track to be supported by the track, I replaced the contents in (what I thought) the same locate from which they were removed from the old crisper drawer. After placing all contents back into the new crisper drawer, I applied a little more rearward pressure until the new crisper drawer was in the fully closed position. I then closed the refrigerator door. I quickly reopened the refrigerator door, to ensure the light went out. It was on. I slowly closed the refrigerator door, keeping an eye on the gap between the refrigerator door seal and the refrigerator cabinet, and noted the light did, in fact, go out when the door was about a half inch from being fully closed. Returning to a fully standing position, I announced to my wife that I repaired the broken crisper drawer. The congratulated me on my accomplishment and I felt a rush of satisfaction over a job well done.

Very easy to install. Followed instructions so took about 1 minute (including unpacking). Saved big money. Great company to deal with

Received new drawer in 2 days and effortlessly exchanged it for broken one. Color of writing didn't match but I just removed it from the old one and replaced it. Very pleased.

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

Simply slid the replacement into place. 30 seconds at most.

I just changed old drawer to new drawer

First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.

Removed old drawer, replaced with new one. Easy fix. New drawer fits perfect.