RMC275PDB4 Whirlpool Microwave Oven Combo - Instructions

My mother and I were having considerable trouble baking or using the wall oven due to the escape of heat because the door wouldn't close properly. She, on many occasions, rested heavy baking pans/sheets on the door which, over years, caused it to "spring". Before I started the project I took a level and saw the door was facing down at least 3/8"-1/2" more than being level. I assumed it was the Door Hinges and after much research I found PartSelect who was extremely helpful in not only advising me as to the exact problem causing the door to not close properly but also in the ordering process itself. Because of the complexity of how the door is assembled I took digital video at various stages: removal of the door, disassembly of the entire door, removal of the control panel, and various small parts of the door - all with audio description by me as I went along. Because it took a few days to order and receive the parts I had time to clean the baked-on, caked-on grease inside all the parts to include the vents on the door and under the control panel using a power-washer when possible. I obtained auto-strength grease cutter/remover and soaked every "group" of screws in separate glass jars with covers (labeled). I also taped screws to a piece of paper, traced them to make sure they went back in the same place, and washed these as I went along. At the time the parts were received they were packaged in a fantastic way - quick shipping, easy to order, and I immediately started to reassemble the door. When I found my video wasn't enough to help me get the door assembled properly I used .pdf files I found on PartSelect which were extemely helpful and with a laptop close by I referred to the video I had taken and also SmartSelect's .pdf files. Because my digital camera was - and is now defective - I lost some of the most important video and this is the reason it took me almost 5-1/2 hours to reassemble the door. I wanted it to be correct given the oven is self-cleaning plus I do not want fires in the house!! All parts were laid out across three rooms and after being like this for almost a week it was great to have the entire oven back together again. At this point the oven door, when opened, is now facing "up" at least 3/4" as opposed to hanging down as it was before this project started. I closed the door and it actually pulled itself shut - something it hadn't done in years! The hinges came with pins already inserted so I didn't have to wrestle with the hinges to insert the original pins. The gasket was the easiest part to replace - simple removal of the old, worn, charred one and pop in the new one using the little clips that came on the hinge. The hinges themselves are extremely strong and well-made. After this project I have to say the oven now looks BETTER than when purchased, my mother has used it to cook with only once and it took 1/2 to 3/4 the time given the door is now completely closed because of the new hinges. I am totally satisfied with the parts, with PartSelect, will keep this site as a reference for further replacement parts if needed, and the oven is positively GORGEOUS after it was thoroughly cleansed of built-up grease. It looks BETTER than a new oven!! THANK YOU, PARTSELECT, for all your help and perfect parts!!

Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

I am not a big do-it-yourselfer, so maybe I might have found this more difficult than expected. When I first looked at the oven before ordering the part, I saw a couple of screws and it seemed like an easy task. However, I found that I had to remove to whole door first, which was actually easy. Then I started to remove the case. Then I removed several layers of a puzzle. Oven door had 3 pieces of glass and 3 metal brackets. The installation video was for a completely different oven. Although I got out the broken glass easily, I had difficulty reassembling. The oven diagram for the parts was even deceiving. I had to involve my spouse and after an hour of cursing everything, we finally managed to get the thing back together. Whoever designed this oven must have been a deranged German scientist. However, everything is back to normal and I probably saved a couple hundred bucks for a repairman.

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

Ordered a new cooking tray and it was shipped within two hours. Packaging was excellent and well protected.

I ordered it from PartSelect one evening and had the replacement glass one day later. It was the quickest service I have ever experienced. Now, I can continue to use my microwave. Thanks for such great & timely service.

By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

Removing the door was the first challenge but once the door was off it was a matter of disassembling the door to get access to the interior door. If you remove all pieces and line them up in the order that they are removed you have a good chance for success.

Went to PartSelect on the internet and looked up my model. Next I selected the problem from a short list of questions, which indicated the broil element was the problem 99% of the time. With this bit of confidence I ordered the part which was delivered in 2 days. The first step in the repair was to turn off the circuit breaker for the oven. After removing four screws that held the broil element in the oven, I pulled the electrical connectors apart on each end of the old element and attached the new unit to the electrical leads. Lastly I pushed all the wiring back inside the back wall of the oven and replaced the four mounting screws. I then performed ops check, which worked. End of story, job done in about 10 to 15 minutes. Easy Peasy.

Once the door was secured with hinge locking pins which I made out of cut off 16 penny nails,I removed the door , layed it on a soft padded piece of vinyl and proceeded to remove the inside top cover which was secured with phillips screws on the top and sides. I was then greeted by 2 sheets of glass before I could get to the front glass which was the one that cracked.These sheets of glass were secures with slotted metal frames which also required removing several screws and braces. I was then able to remove the cracked glass and replace it with the new glass panel. Then I had to reverse the steps to assemble the door which was fairly easy since I made a diagram of the steps when I disassembled the door (this saved me alot of aggravation since my memory isn't what it used to be. The door was fitted into the frame of the oven and once the hinges were in place I removed the pins and closed the door. It was at that point that I got a kiss from my grateful wife. End of story.

Had to screw off old terminal block & screw on new one