RK961G*J3 Hotpoint Microwave Oven Combo - Instructions

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!

Simple, unscrew and then re-screw

Turned off power. Then loosened two nuts at back of oven. Pulled out old element and inserted new element. Tightened two nuts and turned power back on.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

youtube video it took maybe 10 minutes total to replace part. Easiest repair ever. Im a 50 year old woman and when I say it was easy, it was easy!

Removed several screws and removed element. Replaced same. Total ten minutes.

Removed 4 scews from old element and replaced the old element with the new element with the supplyed new screws. It was very easy. The new element works great.

turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set.

The replacement was simple. I turned off the power to the oven, took out two nuts holding the element in place, unscrewed the element from the power and finished the job in 10 minutes. The company that we called was going to charge nearly $200 to complete this job. I saved a lot of money by doing it my self.

Turned off circuit to oven. Unscrewed two screws holding element in place at back oven wall, pulled out old element and loosened nuts holding it to wiring. Discarded old element. Put new element in place and re-attached nuts to wiring (very simple). Pushed back into place and replaced screws to hold plate to back of oven wall. Turned circuit back on and put oven on to bake to test -- voila, success! Thank you PartSelect.com!

Bake element was getting old, thin and burning hotter in various spots. Ordered new part. Upon arrival, turned off power in the fuse box, 2 screws removed the old bake element from wall of oven. 2 more screws disconnected the power supply. Installed new part, reconnected all 4 screws and turned power back on. Entire job took 15-30 minutes, extremely easy.

Turned off power to oven and removed screws attaching element to back of oven with a socket wrench. After removing the screws, I pulled element out about six inches and used a screw driver to remove the screws that attached the two electrical wires to the end prongs of the element. After removing old element, I simply reversed the process to install the new element.