RK777G*T8 Hotpoint Wall Oven - Instructions

Once I saw the gasket that was supplied it was really easy to see how to install it.
A hook on either end of the gasket gave me the clue on how to remove the old one.
Off with the old and on with the new in less than 2 minutes!!
Extremely easy!! Thanks Part Select for having what I needed!

Simple, unscrew and then re-screw

Turned off power. Then loosened two nuts at back of oven. Pulled out old element and inserted new element. Tightened two nuts and turned power back on.

Removed several screws and removed element. Replaced same. Total ten minutes.

Removed 4 scews from old element and replaced the old element with the new element with the supplyed new screws. It was very easy. The new element works great.

turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set.

My husband removed the old element by shutting down the power, then unscrewing the element. Then he screwed in the new element and turned oven on for 5 minutes to break it in.

Very simple and so cheap!

remove 2 screws holding element to oven back wall/ unscrew wires from element/ new element install the reverse of removal

First, I shut off the power to the oven... no point in risking a nice electric shock. The next thing I realized was I could not see anything... enter the flashlight. Then, well then it was really easy. I removed the two screws that held the element to the back wall of the oven, pulled the element (and some of the insulation stuffing) out about 2 inches to reveal the two wires and their connecting screws. Unscrewed them, put the new element in, reconnected the wiring, restuffed the stuffing and reattached it to the oven wall. Turned on the power and she heated up faster than ever. Speaking of fast, my part arrived the day after I ordered it and that was with regular shipping. Thanks fellas.

First I located the circut breaker to the oven- once no power supply was confirmed (oven light was out) I diconnected the screws that held the old element in place. Pulled the old element forward and disconnected them from the wires. The hardest part was getting onto the oven to reconnect the wires to the new element since the door opens down the work space is a little tight and awkward. Connected new element and replaced screws. Done in less than 20 minutes and no repair service calls to pay!

First I removed the two srews that hold the element in place. I then pulled the element out about three inches and disconnected the two wires. I attached the wires to the new element and we had our oven working again. I really am happy with the timely service I received from PartSelect and would recommend them to anyone.

I removed the two screws that held the element panel on. I removed the lead wires from the element, making sure the wires didn't retract back into the wall. I put the new element in, reconnected the lead wires and put the screws back in. I was concerned that the panel wasn't as long (top to bottom) as the previous one and it barely covered the hole, but it works fine. It would have cost me $60 to have it done by my home warranty company so I saved almost half.

If the bottom heating element is not glowing red when you turn the oven on replacing this part may be the answer. Look for a spot on the old element that could indicate it has shorted out and no longer carries a charge.
Very simple to remove the two screws holding the element in place, pull the element out about 3 inches, disconnect the two wires, replace with the new element and reattach the two screws. Simple and effective. The new element is fast and responsive. Do this before any other suggestions to replace more complicated parts in the thermostate etc.

I removed the two screws that held the element in place. I pulled out the element and disconnected the two wires and unscrewed the screws and then place the new element to it. screwed the wires back to the element wires and then push it back in. Replaced the outside plate and screw the two screws back in.

Save myself money by doing it myself.

Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.