RF263LXTQ3 Whirlpool Range - Instructions

Lynn from BRADENTON, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bunner was not shuting off automaticly

I used the replacement video from the web site. The replacement went great.

Parts Used:

Lee from GROVE CITY, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Right front burner would only stay on high

Turned off breaker, pulled stove from wall, took off knob, unscrewed and pull off backing from stove, unscrewed heat control part, unplugged wires, plugged into new part, installed part, replaced stove backing, replaced knob, pushed stove back in place and turned on breaker. It worked fine.

Parts Used:

Brian from YORK HAVEN, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

8” burner on low would run away. Burn solid red.

I installed the new switch. No difference. I switched elements with the other 8”. Same thing. I called Part Select and their rep said he doubted the new switch was defective but if it was they would replace it. But first how about trading the new switch with the other 8” switch that is working. I did that and the new switch worked fine on that burner but the old switch that worked before allowed the bad burner to go to red hot. Now I’m at a loss. All I see is a new stove. I don’t know what to do next and am open to any and all suggestions.

Parts Used:

Paul from SHELBYVILLE, TN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

2 Service Elements Didn't Work (Didn't heat up)

Unplugged old elements and plugged in new ones

Parts Used:

Range Surface Element

Standard Y-Frame Range Surface Burner

Roseann from MEADVILLE, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bake element out

use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.

Parts Used:

Oven Bake Element

Joyce from BALLWIN, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners needed replacing

Pulled out the old burners and put in the new ones.

Parts Used:

Standard Y-Frame Range Surface Burner

Alene from INDIANAPOLIS, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Element had burned out, and the drawer glides were broken .

Replaced both .

Parts Used:

Oven Bake Element

Rear Drawer Glide

Allen from ASHLAND, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I decided it was the switch that was bad as it would not turn on or anything.

After my husband replace it we noticed that our knob was worn to the point it would not turn on the new switch. I am sure the switch was o.k. so kept the old one and getting a knob to fix the issue.

Parts Used:

Christy from OROFINO, ID
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Used part

Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .

Parts Used:

Sabrina from FREMONT, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light would not light

Pop old one out and new one in

Parts Used:

SOCKT-LITE

Frank from LEBANON, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip pans needed to be replaced

1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements

Parts Used:

Mark from ROSENBERG, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven temperature was 50 degrees off

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

Parts Used:

Oven Sensor

Gregory from BRIDGEBORO, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

surface burner heating element broken

took out old element, replaced with new.

Parts Used:

Range Surface Element

Marlene from Charleston, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowls very dirty and stained

Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you

Parts Used: