Models > REX6634PQ0 > Instructions

REX6634PQ0 Roper Dryer - Instructions

All installation instructions for REX6634PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX6634PQ0
1,321-1,335 of 1,819
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer made loud noise, shook across the floor

  • Customer: Miranda from Scottsville, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
By following the repair video available, I took off the top and front panel of my dryer, removed the drum, removed the old drum support rollers, vacuumed out the inside of the dryer (so much lint!), replaced the drum support rollers, and put the dryer back together. Dryer runs like brand new and is very quiet. Repair was extremely easy to do. Got the replacement parts in about 2 business days. PartSelect repair videos make the repair easy too! Lots of satisfaction for a girl to repair her own dryer!

noise while drum rotating

  • Customer: vince from virginia, NE
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
follow the vidio. removed lint screen. removed screws securning the lint trap guide. used to disconect the two clips honding the top cover and lifted it up and secured it as not to drop down. removed two screws at top of front paned and removed it. took out drumb. took off the two rollers and remounted the drumb and belt. replaced front panel and two screws. lowered top panell and two screws. replaced lint trap. turned on to see is noise stoped and it had. done

right side drum roller rubber came off,this caused drum to drop and belt tensioner to release.

  • Customer: John from New Bern, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed two screws from filter chute,raised top of dryer and removed front panel,lifted drum out,replace both rollers,replaced drum,reset belt tensioner replace front panel,lowered top,put screws back into filter chute.

dryer wouldn't heat

  • Customer: Maureen from Sayreville, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The thermal fuse worked and fit but the cycling thermostat was not correct so I paid for a part that was wrong did not fit the model #. The other part was repaired and working in around 20 minutes

unit wouldn't light

  • Customer: mark from burbank, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
bought thermal fuse and thermostat as most likely. Took apart and checked with voltmeter and found the fuse open. Replaced it. Video instructions are helpful as is the part location in the drawings. Real problem was lint had built up in back vent area, blocking cooling/ burner intake air. Went through entire dryer and vacuumed it out

My dryer would not turn on at all

  • Customer: Jason from Richmond, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched your YouTube video about trouble shooting dryers, and found that the problem was my thermal fuse was out. My exact model of dryer was used in the video. I ordered the part and replaced it following the instructions on YouTube. Since the video was so helpful, I decided to order my part from your company

Dryer was running but not producing heat

  • Customer: Anthony from Elk Grove Village, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Most of the time was spent just getting behind the dryer and removing the back panel. It was also a great time to vacuum the area. If you're not working in tight quarters, this repair is really easy. The fuse is not hidden and requires no tools to install (only a wrench to remove the back panel). It started working right away & the part cost significantly less than a service call (about nine bucks + shipping).

Dryer would not start

  • Customer: Gordon from VIRGINIA BEACH, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I followed the video on the website, removing the back of the dryer, then located and removed the thermal fuse, replaced it with the new one..... Presto, it worked... Replaced the back of the dryer and was good to go... Thank you Part Select

no heat no igniter lite no gas flow

  • Customer: Douglas from Saginaw, MI
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced thermo fuse. not the problem. not sure how to test for next step. timer, cycler tumbler all work just won't fire up.

dryer did not work

  • Customer: Donald from Campbell, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplugged unit, removed the back panel replace thermo fuse and replace back panel, plugged electric cord back in and we were back in business. real easy fixx

Gas burner would not fire.

  • Customer: Leif from Plainfield, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys

After 24 years the belt broke

  • Customer: Bill from Springfield, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed top, removed front, laid dryer on back to keep drum in place and replaced belt. Used masking to hold new belt in place while installing. Easy job. Belt was delivered in 2 days. Thanks

Replace dryer belt.

  • Customer: Mark from Dryden, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We followed instructions in videos from this site and youtube. The repair went smoothly and dryer works great now.

old drive belt had broken

  • Customer: Lloyd from LEBANON, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the excellent video instructions for dryer drive belt replacement. The tensioner proved to be a little tricky. I also had to fiddle the drum back into position. Now that I've actually done the repair, it would take half as long if doing it over.

Belt Broke

  • Customer: Dann from Granville, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.
All Instructions for the REX6634PQ0
1,321-1,335 of 1,819