Models > REX6634PQ0 > Instructions

REX6634PQ0 Roper Dryer - Instructions

All installation instructions for REX6634PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX6634PQ0
1,621-1,635 of 1,792
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door switch broke. got terminal block for future replacement

  • Customer: robert from southwest ranches FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
pop the top of the dryer open with a screwdriver(front), leatherman works well, unscrew the old switch,disconnect the wires - new part has 3 wires old one has 2 but the connector fits fine. closed up the dryer. turned it on. it works fine. A long phillips head is suggested (8") to clear the door frame so you don't beat up your knuckles.

Dryer would not shut off when door was opened

  • Customer: Nannette from Expot PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Read how others replaced the part. Ordered the part that afternoon. The part was waiting at my doorstep the next day! I removed 2 screws from the dryer vent, lifted the top, removed the old part and put in the new! bingo! Dryer works perfectly! Thanks for your great service. I will recommend you to everyone!

door switch defective

  • Customer: Peter from Blaine MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I WORK WITH A PHILLIPS SCREW DRIVER AND A FLAT SCREW DRIVER I PRY THE BOTH SIDES IN FRONT TO LIFT THE COVER I PROPPED IT TO AXCESS THE DOOR SWITCH WIRE THEN I OPEN THE DOOR TO REMOVE THE TWO SCREWS I REMOVED THE TABS FROM WIRING AND I DID THE REVERSE TO ASSEMBLE THEN PLUG THE CORD BACK ON THE WALL IT TOOK ME LESS THAN FIVE MINUTES. THANKS FOR YOUR ADVISE ON THE DEMONSTRATION ON THE VEDEO CLIP THANK YOU FOR THE SWITCH TOO MERRY CHRISTMAS..............................

broken belt

  • Customer: Mandi from El Dorado AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I loved the demo video on how to do the repair-it was very helpful. My dryer was different than the one on the video, and I had to make adjustments ( I had self tightening screws on the top and bottom of the front panel and then I stripped the screws)I did this by myself and I had to prop up the drum AND the front panel with items in laundry room.) That's why it took me longer than demo (also had to run to hardware store to get screws). Felt great to accomplish this by myself. Thanks!

Dryer drum would not turn

  • Customer: Peter from Evanston IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I researched the issue, found a video and ordered the belt, which came in 2 days. It was inexpensive, and I had my dryer back and running in less than 3 days. I did get my son to help me as it might not be that easy with just 1 person (to hold the drum in place while putting the front back on). Great service and great information on how to do the repair.

Belt Broke

  • Customer: Dawn from West Sand Lake NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
When we ordered the part we watched the video, to see what needed to be done and both my husband and I got the dryer all ready for install before part came so when the Ups delivery came it took all of 10 min to get it back up and running! Thank you so much for having the details and a video made thing go so well! Sincerely Dawn

Torn dryer drum belt.

  • Customer: Donald from Allentown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front dryer panel removed torn belt and replaced it with the new belt.The job was easier than i thought.

dryer belt broke

  • Customer: mary from wimberley TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
ordered the part late sun. afternoon. arrives ups on tues.am. took dryer apart and replaced belt and up and running in about hour and half. works great. dyrer is about 25 yrs. old.

The drum quit turning

  • Customer: Paul from Bryan TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Sunday, the drum on the dryer quit turning. I could hear the motor running, so I guessed that the belt had broken. I jumped on the internet and searched for Roper Dryer parts and Part Select jumped up. Within 30 minutes, I had a new belt ordered. I received the e-mail with the how-to included and boy did it save me some hassel. I was prepared to do it all wrong until I saw the video. When the belt arrived, it took me longer to gather the tools I needed than it did to change the belt. Thanks

no visual access to the area we trying to work in.

  • Customer: Preston from Ventura CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
To start off I am disabled so I had my 14 year old daughter to help me.I opened the top of the dryer,disconnected the door button and had my daughter help wire the top open and take off the front panel.We took this time to clean out the dryer for it was quite built up with lint.I then gave my daughter my cell phone and told her to stick it in the dryer to take pictures of the area we needed to work on.I then showed her the pictures and explained in detail how everything worked and what she needed to do.I then put the belt around the drum and she proceeded to put the belt on the pulley and tension rod.At this point we are both filty and both have gotten miner injuries.I spun the drum and it and the belt both spun,we thought GREAT we have fixed it,so we put it all back together,plugged it in and nothing.So we take it back apart,but this time I stick my hand in there and find out she didn't have the belt on the pulley,it was wrapped around the tension rod so I fixed that problem.Then I figured out that she hadn't pulled the tension rod over to its proper place so I do that as well.This time I spin the motor fan in front to make sure we have it right.We put it all back together, plug it in and it WORKS,so we throw the jeans in because we have to be at a B DAY party in a couple hours.The dryer buzzer goes off and we both go to check and the clothes are soaking wet.I open the top of the dryer and the brand new belt is broken.So many mixed emotions at this time I cant tell you how disappointed and upset we where.So she took her jeans out and used a hair blow dryer to dry them and I hung the rest all over the house.So I decide not mess with the dryer for a couple days because of my frustrations with it.We have to do laundry everyday,I have three teenagers,so I have clothes drying all over my house every day.Even went to the laundry mat once $40.00 it cost me.A couple days go by and I decide to see what happend. This time I have my 15 year old daughter help me.I completely disconnect the dryer from everything.We put it on top of A table and take it apart.What do I find?the motor pulley is broken and has jagged edges the shredded a piece of the new belt.As I mentioned earlier I am disabled and am on SS so I only get paid once a month and have no extra money so now I have to wait until the end of November to order another belt and the motor pulley.In the mean time there is wet laundry hanging all over my house with fans blowing on it to help dry it faster.So what was supposed to cost approximately $20.00 to fix is now going to total over $100.00.I do thank you for the speedy delivery of the dryer belt and we had A great time at the B DAY party.thanks

broken belt

  • Customer: Mark from Ridgway PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the belt

broken belt

  • Customer: john from estill springs TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
even though the motor pully was invisible to me, i was able to, by feel, thanks to your diagram, install the belt.

Dryer not heating, bad thermostat

  • Customer: fred from clemmons NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replace with new element since I had the back off. Might as well do high limit and tstat. Since the dryer belt was very old I decided to replace it also. The repair was very easy since the parts matched perfectly.

Broken Belt

  • Customer: ANDREW from MOUNT UNION PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Fast shipping. Part arrived the next day!

Ribbed belt broke

  • Customer: richard from satellite beach FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions you supplied. All went well. The short movie that you supplied was fine but the only tricky part which included placing the belt over the idler wheel was not well done in that the repairman's arm covered the work area. Delivery time was excellent.
All Instructions for the REX6634PQ0
1,621-1,635 of 1,792