Models > REX4634JQ0 > Instructions

REX4634JQ0 Roper Dryer - Instructions

All installation instructions for REX4634JQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the REX4634JQ0
31-45 of 1,712
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bought motor, then bought blower wheel also

  • Customer: Daniel from Coatesville PA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 37 of 48 people found this instruction helpful
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!

Dryer motor would not turn on

  • Customer: John from Bluffton SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 32 of 34 people found this instruction helpful
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.

Replacing worn drum support rollers and shafts.

  • Customer: Gary from Canton CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 32 of 35 people found this instruction helpful
Very easy once I figured out how to open it up to see what was the matter.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.

Good luck, It s not as bad as it sounds.

Needed new Lint Filter for Dryer

  • Customer: Diane from Rancho Cucamonga CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 26 of 27 people found this instruction helpful
Went to 3 big appliances stores - Not one carried any type of Lint Filter for Dryer. Went on line & typed in Lint Filter for Dryer in search bar. Part Select came up. Went thru site to ordering - Part Select made so easy to order. You just type in your Manufacture name & they instruct you step by step how to find model number & type of filter you need. So Easy. Very economical. I ordered & within 4 days I had my filter. I used 7-14 day delivery & was so pleased I had my filter within 4 days. Parts Select sent me email verifying my order as well as email when the part shipped.
Wonderful Customer Service. I will definitely use Part Select for any need part on any appliance.
Easy - Economical & One Stop Shopping. Love it

The Dryer had no heat

  • Customer: Michael from Plano TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 26 of 28 people found this instruction helpful
I ordered up a new heating coil. It was plug and play, real easy to do. Make sure to turn on the dryer with the before you put it back together to make sure the heating coils heat up. Be careful though, it will get real hot, so run for a second or two. Also, you may see a little smoke as the coil burns in, that should be fine. Once it is tested and works, let it cool off, then reattach it, put on the backplate and you are done!

the dryer only blew cold air

  • Customer: charles from waukesha WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 26 of 29 people found this instruction helpful
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)

Dryer belt snapped

  • Customer: J. from Oakdale NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 26 of 30 people found this instruction helpful
There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.

The dryer would run i.e. the drum would turn, but there was no heat so the clothes didn’t dry.

  • Customer: David from Joppa MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 25 of 28 people found this instruction helpful
I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.

Dryer had heat intermittently and would take 3 cycles to dry a load of clothes

  • Customer: ANTHONY from MONROE NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 25 of 30 people found this instruction helpful
First, remove the back panel of dryer which is about 10 screws. Then remove the 2 thermal switches, one is above the heating element and the other is where the hot air comes out. They are both really easy to get to and the pictures on Part Select.com are identical, so you can order the part first and then just "match them up" if you are not sure what to replace. Oops, the first step is to unplug the dryer.

Dryer would run without pushing the Start Button

  • Customer: Donald from Kanona NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 25 of 29 people found this instruction helpful
Turn off the circuit breaker ( Or remove the Fuse/s )to the dryer,

Removed 2 screws that hold the control cluster to the dryer top. Then I slid the control cluster forward and up to release it from the dryer. then I removed the start button knob to the start switch by pulling on it straight out. Next I removed the six 1/4" hex head screws from back of the removed control cluster. Then using a flat bladed screwdriver I pried up the tab coming off the switch housing. just enought to allow the switch to be turned a quarter of a turn counter clockwise which allows the switch to be removed from the back of the control cluster. Next with a pair of long nose pliers gently pull straight up on the 2 wire terminals attaching wires to the switch. Make a diagram before removing them so that they can be put on the new switch in the same way. Then orient the new switch with its tab located a quarter turn counter clockwise from the hole you pried the old switch tab from. push down on the switch while turning it clockwise 1/4 turn so the tab on the switch drops into it's locking hole. Then using your diagram put the wire terminals back on the switch terminals in the same order and position they came off. Replace the Control panel with the screws you removed. Next position the control panel feet over the holes for them in the top of the dryer and push back a little on the panel to lock it in the correct position. Then take the two longer screws and put one on each side of the panel at the correct angle (not straight up and down) but tilted forward to match the holes and carefully tighten the screws. Next carefully replace the push to start knob on the new switch. Turn the Circuit Breaker (or reinstall the Fuse/s) for the Dryer back on. Then test and make sure that when you select the cycle and the door is closed that pushing the start switch causes the dryer to start. You have done it!

No power

  • Customer: Nick from Brandon FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 25 of 29 people found this instruction helpful
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.

replaced heating element in my dryer

  • Customer: Marlene from Indianapolis IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 28 of 39 people found this instruction helpful
I wasn't sure if I was going to be able to do the repair myself. Happily, I was able to and my dryer works like new ! I figure I probably saved about a 100 bucks doing it myself rather than calling out a repair man. Oh, did I mention I am female and didn't have to have a man do this for me. :)

dryer would not heat

  • Customer: Leon from Jasper AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 25 of 31 people found this instruction helpful
I removed the four screws holding the
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......

the dryer element was not coming on and looked like it had burned up

  • Customer: Benjamin from Greenville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 25 of 31 people found this instruction helpful
i decided to order the new element which was the most expensive part then decided to add the thermostats just incase they were bad because they were rather inexpensive. got the parts in took the back off the dryer located the parts i ordered and simply replaced them with the power cut off to the unit. put the back on and it heated like it was better that new my clothes dry 5 times faster than it did when i bought the thing.

Drum stopped turning, fan continued to blow

  • Customer: Richard from Davie FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 22 of 23 people found this instruction helpful
Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, etc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.
All Instructions for the REX4634JQ0
31-45 of 1,712