REX3514RQ1 Roper Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer wouldn't turn on
When the part came in. I unplugged the dryer. Pulled it away from the wall and took the back off. I pulled the wires off the old fuse and plugged them in the new fuse, then unscrewed the on nut that held the old fuse. Then slid the new one in and put the nut back on. Plugged the dryer in and it worked. So I unplugged the dryer and put the back on.
Parts Used:
-
pamela from ocean springs, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door switch broken
Tough part was figuring out how the top of the dryer was secured. Remove lint screen and remove (2) phillips-head screws. (2) clips under from edge of top - I pushed the center tab in, but I don't know if it was necessary. Pull top toward from of unit and then lift front edge. Prop up to work on door switch. Very good access. NOTE: Remove switch screws before disconnecting switch wiring. I didn't and dropped the switch into the bottom of the unit. Had to go fishing.
Parts Used:
-
Robert from Point Pleasant, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Noisy tumbler & worn lint trap seal
Followed procedures in Parts Select web site video
Parts Used:
-
Pedro from Brunswick, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would run, but not heat
Removed the back panel, found the fuse and replaced it. Easiest thing I've ever done! I was expecting it not to be the problem, but I started with the "most common" issue via the website. Voila...it was the problem!
Parts Used:
-
Kenny from Euclid, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Dryer was not producing heat
Installed new heating element. Simply watched the provided youtube video and replaced the heating element. Job took approximately 30 minutes from start to finish, very simple fix. Saved a couple hundred bucks by doing it myself and I have limited knowledge on dryers!
Parts Used:
-
Ryan from Ottawa Lake, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Plastic catch broke
little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install
Parts Used:
-
Charles from North Chesterfield, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Indicator lights blinking, not drying, auto settings not working
Unlike your video, with this model, the thermal fuse is located near the front of the dryer, which I didn't find out until the back was already off.
Parts Used:
-
James from Frankfort, KY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dry door latch broke
I watched the online video first, which made the removal and installation fast and easy.
Parts Used:
-
George from Melbourne, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Parts Used:
-
Betty from Erie, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!