REP3822DW1 Roper Dryer - Instructions

I called the 1-800 number, spoke to Nicole who took down the model number I gave her and she ordered me the part which arrived in a couple days and I popped in right in. This was the easiest repair I have ever made. Nicole's professionalism and knowledge was great and I would order from this company again anytime.

Followed procedures in Parts Select web site video

little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install

I watched the online video first, which made the removal and installation fast and easy.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

After removing the front of the dryer it was evident that the blower boss had broken where the motor shaft comes through and is attached. I removed a few more parts to make the blower more accessible and removed it. I then machined a new boss and attached it to the blower and reinstalled it.I then did a quick continuity check on the three thermostats since the dryer was already apart.I discovered one was faulty and ordered a new one from you.That repair took all of five minutes.The irony of the whole thing is that while I was ordering the thermostat from you,I asked out of curiosity,if the blower was still available. As it turns out it still is but the new machined part worked out great and the dryer was back up and running in no time.

Thanks again,
Dave

I watched the video provided first to get an idea of how it should go. The dryer I have had a different kind of door, so those instructions didn't apply. You probably don't want to publish the way I ended up fixing it, but it did work eventually. Saved me over $500!! Thank you!

Ordered new rollers from PartSelect. I followed the video to replace the rollers. Everything went well. The video did not show how to put the belt back on. I then went to replace broken belt and there was the way to go through the pulley. Works great with no noise. Just like new. Thank you

layed the dryer door side down, took 6 nuts off back metal panel, then took the bolt off at bottom and reached in and pulled drum support rod loose, removed old roller, installed new roller, reached in set drum support rod back into hole where the threads were showing on the outside where the nut was then put back on and tightened back up, put a pair of vicegrips underneath on rod to hold in place while tightening up nut,placed cover panel back on with screws and now it works like a new one, runs very quiet. Cost was 25 dollars for part nothing to do it ourselves. We priced new dryers that size they're well over 400 dollars. Easy REpair!!

For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.

ordered wrong limit switch had to reorder right switch and decided to replace the heater element as well. works fine now

Read the Use & Care Guide! I spent several hours trying to repair a dryer that was not broken because I was unaware of the "lint signal". While replacing a burnt out heater element I apparently disturbed the flapper on the lint signal box and it stuck in the open position. My wife who does the laundry has always kept the lint filter clean so we had never heard the lint signal and I assumed that the high pitched sound I was hearing must have been from a faulty gasket, belt, roller, pully, or motor. Boy is my face red!

Watched the how to video on the parts select site. The job to replace the motor was easy although I had some issues with the blower fan wheel as it is made of plastic and was frozen to the motor, yes I turned it the correct way for the left hand threads. I ended up distroying the blower fan wheel and had to buy a new one. I had to remove the rear plate to get at the fan component, but thta was easy to do also. This site should add a "Sometimes bought together" comment for the motor replacement. After all was done I read some of the other comments and found some others had the same problem with the fan wheel. Once I had all the parts the dryer went back together fairly quickly. The job was easy to do and I would believe almost anyone could do it.

replace the water valve

just the way the video showd me