REL4632DL1 Roper Dryer - Instructions

1. Opened the top. (UN-plugged it first) by prying between top and front of machine.
2. Disconnected the door switch
3. Removed two screws one each on top corners of front
4. Pulled top of front cover forward and lifted up to remove.
5. The drum will fallout if not careful, good time to remove drum to clean dust from inside machine.
6. With drum in place slide new belt, skinny side down around drum, to about halve way back.
7. While supporting drum reach back to the motor area, should be on right side facing front of machine. There you will find the belt idler/tension assembly.
8. Thread the belt through the assembly and around the motor drive pulley.
9. Ensure the tensioning assembly is firmly in the slots on floor of machine.
10. Reassemble housing in reverse order. took about 45 minutes

took the back panel off by unscrewing all the little nuts..replaced thermal fuse and put back panel and screws back on...

I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.

Followed your instructions. Was ready to purchase all 3 fuses or components and the lady from NS suggested would only need this Thermal Cut-Off Kit. Right on. I would and will recommend your service to anyone in need. Many Thanks

Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.

I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!

Used wire schematic and locate thermal fuse. Disconnect power and remove rear panel. About 8 screws. Remove the two wires from fuse and check fuse continunity. Fuse was open and prevented power from going to gas solenoids. Replace fuse and clean exhaust ducts. Dirty ducts might have caused fused to over heat.

I went on the PartSelect site and watched some videos to determine what could be wrong. I almost guessed and bought the wrong part as there were a few. I ended up spending $17 for a multi tester. Once I determined that the thermal fuse was bad. I just followed the instructions from the video and replaced it. Took me more time figuring out what part was bad and buying the tester than actually replacing the part. Very glad I bought the multi tester watched the videos. After that it was easy.

Removed back of dryer. Removed old parts. installed new parts. Thermal cut-off instructions stated to install using screws included. There were no screws included in kit. Had to use one of the screws that holds the back on to the dryer.

Followed video found part son replaced it worked!

I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came across your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!

I followed the video provided by PartSelect. It pretty much went exactly like the video said it would. I was pretty sure the belt or idler pully must be the culprit, but I didn't even know how to open the thing up until I saw your video. I would likely still be putting up with the squealing without that video. Now the dryer is nice and quiet. -Mike

First watched the video you sent me then changed out the parts in question. Slicker than pig snot on a door handle! Once back together we did a load of laundry. The unit worked like the day it was new.

I decided to repair it myself, and after ordering the part from partselect.com, and getting it very quickly I installed the heating element and, viola, the dryer works great again. All the info necessary for simple repairs is available online for most major applainces, and if you a little basic mechanical know-how, it isn't that hard. I just wish I would have just ordered the part from partselect.com right away!

I followed the excellent video instructions for dryer drive belt replacement. The tensioner proved to be a little tricky. I also had to fiddle the drum back into position. Now that I've actually done the repair, it would take half as long if doing it over.