REL4622BL1 Roper Dryer - Instructions

I unplugged the dryer then removed 2 Phillips screws from lint trap. Then I popped the top up on each top corner with a screwdriver. I removed the 2 screws holding the front cover. I unclipped the wiring connection and moved the panel. I took out the old belt, put the tensioned back on then put the new belt around the drum and held the drum up with my shoulder then put the belt through the tensioner and put it on the motor spindle by pushing the tensioner back. I put it back together and it worked perfectly. Your video was very helpful. Job was very easy.

Had my wife call the repair man. Since it was Saturday afternoon, no luck. YouTube help me diagnose the problem. I found that the drum belt slipped off the idler pulley assembly and the assembly was laying on the floor. I noticed that the belt was frayed and was probably stretched out which may be why the belt slipped off in the first place. I glued the frayed pieces of the belt back with gorilla glue and clamps. You Tube helped me mount the idler pulley assembly and string the belt correctly. I then ordered the replacement parts through your website. The parts came to my home in a few days and I will fix the dryer properly when I get a chance.

The instruction sheet that comes with the parts is excellent. Follow it and all goes well. Be patient and stay away from the sharp sheet metal edges present in all such appliances !!

What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

there were 5 ,1/4 screws in the back panel . The heater box was right at the rear when the back was removed.. Replaced the two controls that were in the kit with a 1/4 nut driver. Checked the terminals for tightness and contact. No discoloration on contacts. Ran unit after reassembly for 20 min cycle to test ,Put into service

Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

Took the back cover off. Replaced fuse and put the cover back on. Worked great.

I ordered the Thermal Fuse, as it appeared to be the problem. A friend suggested that as long as the price was fairly reasonable, I should go ahead and get two of them and keep one for later. I ordered/paid for two of them. I put the Thermal Fuse in, and when I attempted to turn the dryer on, it ran for about 5 minutes, at a very hot heat, dried the towels, and then would not come on again. I thought it had kicked the circuit breaker, but after checking, found it hadn't. I watched the youtubes.com again and found that there were three other parts that it could possibly be. I ordered them, and replaced all of them. One of them had 4 prongs but two on the new one. I left two wires off, and sure enough, it would not run. I borrowed an ohm meter, and found out my old part was still good, but that in the process it had blown the Thermal Fuse, of which I just happened to have an extra, and after installing it, it is now in perfect running order. The total repair was about $80-100, rather than a $75.00 bill for service and heaven only knows for the parts at the repairman's price! Thanks youtube, Parts Select and my friend for his advice! Walter

Removed vent hose. Removed back of dryer. Raised top lid of dryer. My model only had a half removable back. Removed screw and spring clip from top of heater chute. Removed wires from heater element. Pulled back top of heater chute. Removed heater chute. Removed screw holding heater element. Removed element. Slid new element in chute. Replaced screw. Replaced chute on dryer. Replaced spring clip and screw. Reattached heater wires. Set dryer top down in place. Plugged dryer in. Turn dryer on to make sure it was working. Replaced back plate on dryer. Reattached dryer hose. You are finished

After removing the back, I realized I absolutely did not know what I was doing. I went to google put in my model number, and went to your web page. The rest is history. Went to the video watched it and went back to the dryer and after cleaning up the back, put it back and removed the top and front as per video. The parts came in a few days and replaced the belt and idler arm n about 2 min. I am not kidding. The wife held the drum while I put the front back on. One thing I could not separate the door switch so I just unscrewed it from the fron panel. The dryeris 20 years old, and your web page will put the Maytag repairman on the unemployment line.

I followed the instructions on the Part Select website for drum support rollers and shaft. The videos were great! (There wasn't one for the right side shaft but I could extrapolate from the other instructions.) The hardest part for me was releasing the dryer top - the video made it look so easy but it took me a long time to get the little clips to release with the putty knife. Also, tightening the new right side shaft required the help of another person as my arms are not long enough to hold the shaft with pliers while I tightened the nut in the back of the dryer (and I did have to remove the back cover for this shaft). I would recommend to anyone even a little bit handy to attempt a repair following part select's videos.

I follow the instructions from the video sent to me with the email to tell me my new belt was shipped. Made the whole job go a easy as could be. Parts Select made fixing my dryer so simple and I also got the belt within 2 days. I recommend buying parts only from you! Glenn

I repaired this dryer after I did a little research online to learn about the thermal fuse. I took the back off the dryer and used the Fluke meter to test the thermal fuse for continuity. There wasn't any. I left the dryer disassembled and ordered the part. It arrived two days later. I installed it and reassembled the dryer in just a few minutes. It was a pretty simple repair.

The PartsSelect video was great. I'm not sure I would have figured out the trick for opening up this dryer without it. After that the main problem was getting goop off of the drum support roller spindles. This took lots of solvent and elbow grease. I think this was the main source of noise. The oil had turned to something like partly dried glue. They were very hard to turn. The belt was intact but badly cracked. The idler probably could have been oiled and reused but I already had the part so I replaced it. Everything went just like the video. The dryer now hums along like a new one!