REC3422AW1 Roper Dryer - Instructions

very easy had to do some rewirng.who ever had it before me bypassed the fuse and several other things.

Took screwdriver popped out old latch in cabnet. Took pliers popped out latch out of door. Snaped new latch parts back in.

Removed rear panel screws carefully removed panel with out disconnecting wire harness located thermal fuse removed 2 screws removed the 2 wires with needle nose pliers put new thermal fuse in connected the 2 wires carefully put panel back on and tightened screws turned on power and start got heat problem fixed

I diagnosed the problem using the web page. It said that 60% of the people with my problem bought the Thermal Fuse. I unplugged the dryer AND cut the power at the fuse box. I used a screwdriver to remove the vent hose, a nutdriver to remove the back of the machine. The thermal fuse was right there. Removed the old one with a screwdriver, unplugged the wires from the old one and snapped on new one, and screwed it back in. Re-installed the back of the dryer and the vent hose and Whoila! It works like a champ.

Repair was very easy simply used a screwdriver to remove the cracked old latch and used my fingers to insert my new latch.

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

Removed front and back covers on dryer, screws on top and down one side to spread cabinet to remove drum,removed blower cover to get access to shaft nut on that side. The other is accessible. I found that both shafts can bethe longer of the two that were sent. The shorter shaft is too short and needed to be modified to let the roller come outward to lay in the grove in the drum. I will get a longer shaft and replace it.

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.

I first came to the internet to resolve what was wrong. After finding the video I thought was correct I started. I used my volt/ohm meter to check the thermal fuse as instructed on the video and that was the problem. I ordered the new thermal fuse from PartSelect late in the day and it was in my hands the next evening. With in 20 minutes the dryer was doing what it was suppose to do. The hardest part was getting the back cover of the crier off and that wasn't to bad.

1) removed three screws on the top back 2) removed top 3) removed two screws holding the front on 4) pulled front up and it came off 5) cleaned out dryer 6) put belt back on according to a video on Youtube 7) put it back together and my 35 year old dryer is as good as new

I tried all standard tricks: checking circuitry, switches, etc. Then I read other submissions on your site, which suggested this thermal fuse was the culprit on almost 50% of cases. I got yours in 2 days, installed in no time, easy as pie. One caution: it will take an entire day if you forget to close the dryer door completely.

Went thru all the electrical connections, finally checked the thermal fuse. . It was the culprit. Next time I start there. Unlike older dryers, where one component gos such as the drum belt or the heating element and its only 2 years old. This thermal fuse shuts down the entire unit when it malfunctions

I took rear panel off with a nutdriver 8 screws.disconnected the 2 wires that went to thermal fuse and removed 1 screw holding it in place.replaced thermal fuse and reconnected wires and rear panel.turned dryer on. had heat. walk in the park!

Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.