Models > RBD305PDQ14 > Instructions

RBD305PDQ14 Whirlpool Oven - Instructions

All installation instructions for RBD305PDQ14 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RBD305PDQ14
61-75 of 118
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken inside glass

  • Customer: Charles from Georgetown TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
opened door and secured the open position with a 3/8 allen wrench through the hole at the base of the support arm. (small bolt or other round, short object can be used). This locks the door in a 75% open position. Locking the door open allows easy lift and removal. Six screws and the door is apart. Clean and reassemble.

THE INNER GLASS DOOR WAS SHATTERED

  • Customer: JACOB from MIAMI FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I ORDERED THE PART ONLINE AND AFTER RECIEVING IT I DOWNLOADED THE MANUAL FROM KITCHENAID ONLINE AND IT EXPLAIN EXACTLY HOW TO REPLACE THIS PART AND I FOLLOWED THE INSTRUCTIONES AND IT WORKED WITH NOT TOO MUCH DIFFICULT . IT TOOK ME ABOUT AN HOUR BETWEEN REEDING THE INSTRUCTIONS AND DOING THE JOB ITSELF

cracked inner door glass by my cleaning lady (my wife)

  • Customer: REX from BUENA PARK CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
1) Look for the part at partselect.com, make sure you have the model and part number ready. Once you find the part, don't order yet. 2) Start your do-it-yourself repair by removing the oven door. On each side below are two arms/hinges, look closely and you will find locks on each side. Use your finger or flat screwdriver to slide towards you (this is where you start clicking your camera in evey step). Once you did it, wiggle the door a little bit, make sure they're unlocked, then pull it out carefully and hold it tight since it's little heavy. 3) At this point, you only need the phillips screwdriver. Look for all the screws, and unscrew it all, one step at a time (again make use of your digital camera). Remove the parts one at a time until you take out the broken inner glass. Measure it against the dimensions shown in the partselect.com. At this point you feel comfortable putting it back in-reverse, then you order the part. It took me 3 days for the part to arrive, but it's no big deal. 4) It's a bit difficult for me the first time, I can't figure out how to put them back (that's why I recommended the digital camera), plus I have to clean the inside and the other two glasses so it took me 1-2 hrs. I assure you if you follow my instructions, 15-30 minutes max, no sweat. 5) My wife promised me $300 for the labor (competitive price), I'm still waiting though.....Good Luck

Replacement of inner glass

  • Customer: Mark from Kingsport TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

The interior oven door glass was broken

  • Customer: Dante from Apex NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I found some of the feedback posted on this site very helpful. Taking photos as I went along was also very helpful in remembering how to put it back together. There are several over-lapping pieces to the door and you have to be careful to put things back together in the correct order. Lining up the screw holes on the hinges with the door is also a little tricky.

broken inside glass

  • Customer: Rene from Keller TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced

inner glass broken

  • Customer: J from Niceville FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
fairly easy. took a while to reassemble. otherwise all was ok.

Broken Glass Replaced

  • Customer: Tom from Rancho Santa Fe CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
XLarge pizza tray in a 450 degree oven - slam the door & CRACK. Replacement glass arrived on Saturday - VERY FAST DELIVERY. Placed 2 allen wrenches in both hinges - open the door half way & lift up. Place the door on a towel. Removed 6 screws, lift & seperated the inner oven covering, removed the broken glass & cleaned inside & replaced with new glass. More time was spent cleaning & coming up with a tool to fit into the hinge

inner glass broke (water on hot glass, not good)

  • Customer: eugene from Roseville MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I did not take the door off the oven, i dissassbled it in place. all the visible screws on the door have to be removed. The "vent" air diflector or what ever it is , between the upper and lower doors has to come off also to access the screws that hold the front of the door on. The only confussion i had was the bracket that holds the third layer of glass. I forgot that it is held on with the same bracket/screws that hold the secound layer on.

oven wouldn't heat after self-cleaning the oven

  • Customer: Joi from Higginsville MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 12 people found this instruction helpful
The website and diagram of my oven helped me know exactly what was wrong and where to locate the problem. I simply removed the oven door and the trim, pulled the oven out of the wall. After removing the back panel I located the part and put in the new part. Then reversed the procedure.

oven would not heat up in bake or broil

  • Customer: Tom from Fallston MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

circuit breaker blew

  • Customer: Richard from Sarasota FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Inside oven door glass was cracked as I tried to clean after self-cleaning oven.

  • Customer: Jane from LIttle River SC
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
As I did not have a manual, I found all the website instructions very helpful. I had quite a hard time after installing the glass to figure out how to put it back together. The insulation between the oven glass is tricky to keep in tact. I also did not have allen wrenches to keep hinges open, so I used a variety of large bolts and screws. Finally after lots of hours, and almost calling a repairman, I did do it!

Oven locked and heated up, we then shut of the breaker. After resetting the breaker the oven would not turn on.

  • Customer: Dale from SPOKANE WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed the old thermostat took off the conectors then replaced with new one, and screwed it back on.

Spilled liquid on hot door glass

  • Customer: Donna from Castle Rock CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Hardest part was getting the oven door off. Since I bought this house with oven already in place, I had no owner's manual. Tried to get it off with tips found on this site, no go. Went online and found the manual which said to insert allen wrench in holes in hinge, then lift up FROM THE BOTTOM. That is the key. Got door off, then found that replacing the inner glass is a multi step process that starts with the outside door, then multiple brackets to the next inside glass, then more braces to next glass, then finally you are at the broken (inside) glass.My advice would be to take pictures on cell phone or whatever of each level, so you know what goes where when you put it all back. I figured it out but would be faster with a picture. Anyway, got all together and the oven works fine, door looks great!.
All Instructions for the RBD305PDQ14
61-75 of 118